是德科技 | KEYSIGHT
941-0095 传输测试仪 详细指标
Test interconnects and emulate traffic up to 1.6T per port
Part Number 941-0132
941-0133
Interconnect and Network Performance
Tester 1600GE-C OSFP1600
2-Port
Performance Tester
1600GE-C
OSFP1600
2-Port Rackmount Chassis
二、Hardware Fixed Chassis System Specifications
Number of ports
2-port OSFP1600 chassis
Physical interfaces Native OSFP1600 physical front panel pluggable ports
Default speeds included with the chassis
• 1x1600GE, 2x800GE, 4x400GE, and 8x200GE per port, PAM4 over
212 Gb/s electrical
• Optical transceiver and fiber cable interconnect support for all speeds
• Active and passive copper cable interconnect support for all speeds
• (Planned) 1x800GE, 2x400GE, 4x200GE, and 8x100GE per port, PAM4 over
106 Gb/s
Number of users
2 users per chassis (1 user per front panel physical port ownership)
Interface protocols specifications for 1600GE/212
Gb/s electrical lane support
IEEE P802.3dj Media Access Control Parameters for 1.6 Tb/s and Physical Layers and
Management Parameters for 200 Gb/s, 400 Gb/s
800 Gb/s, and 1.6 Tb/s Operation
Layer 1 support
1600GE PAM4
speeds for 212 Gb/s electrical
• PAM4
1600/800/400/200GE speeds
• KP4 (RS-544, 514) Ethernet Forward Error Correction, IEEE 802.3 Clause
119
• FEC symbol 误差 injection · 全部速度
• FEC Codeword symbol error correction distribution statistics
• PCS Rx per lane and port statistics
条件:analysis. Additional test, pattern controls and pattern detection are included.
• Layer
1 BERT with PRBS-7Q, PRBS-9Q, PRBS-11Q, PRBS-13Q, PRBS-15Q, PRBS-23Q
PRBS-31Q and SSPRQ (Tx only) pattern generation support and Rx-side statistics and
OSFP1600 optical transceiver
support · • Support for OSFP1600 specification
compliant optical transceivers up to 40 watts
of consumption (Power Class
8 and higher)
support · • Support for OSFP1600 specification · • Support for OSFP1600 specification
compliant optical transceivers up to 33
watts of consumption (Power Class
8
条件:• INPT-1600GE-C hardware supports these transceiver types: Fully retimed optic (FRO).
Low Power Optic (LPO), Linear Retimed Optic (LRO, aka RTRL) optic.
• Please consult the factory for additional transceiver support information from various
• See Optical Transceivers under the Ordering Information section of this data sheet for
purchasable optical transceivers for this product
OSFP1600 Active and Passive
• Supports CMIS 4.0
5.0 and 5.3 specifications including read/write access to all CMIS
• Supports C-CMIS
1.0 (Coherent CMIS)
• Supports Application Selection Code (AppSel) feature of CMIS with auto-detection and
transceiver configuration support
• CMIS will operate with optical and copper interconnect media to the extent they are
supported by the interconnect manufacturer
• CMIS is exposed through the Interconnect Test System software option (930-3360) with
REST API/Python and Interconnect Library, and the built-in IxExplorer application and Tcl
Part Number 941-0132
941-0133
Interconnect and Network Performance
Tester 1600GE-C OSFP1600
2-Port
Performance Tester
1600GE-C
OSFP1600
2-Port Rackmount Chassis
Digital Optical Monitoring (DOM)
Automatically provides information from the interconnect device plugged into the test port, along
with the device status, electrical power, temperatures, power class, laser power and various Loss
of Lock (LOL) and Loss of Signal (LOS) threshold and alarm monitoring information. The DOM also
provides feedback when alarms and thresholds are exceeded. This capability is provided with the
IxExplorer and IxNetwork applications.
1600ZR Coherent Optics
• CMIS 5.0 and 5.3 and C-CMIS
1.0 (Coherent CMIS) provide Read/Write access to all
management pages and Versatile Diagnostics Monitoring (VDM) registers via IxExplorer
GUI 和 Tcl 测试 automation 编程接口
• Supports the Application Selection Code (AppSel) feature of CMIS with auto-detection
and configuration support
条件:consumption optical transceivers before conducting long duration tests.
• The IxExplorer application supports the Digital Optical Monitoring (DOM) feature that
automatically monitors and reports the module case temperature, temperature warning
limits, and the maximum temperature threshold limits. It is highly recommended that the
DOM feature be active to monitor the temperature behavior of installed high power
• 17.0” (L) ×10.86” (W) x
8.06” (H)
• 431.8 mm (L) x 275.7 mm (W) x
204.8 mm
• 26.95” (L) x 8.64” (W) x
3.34” (H)
• 684.5 mm (L) x 219.4 mm (W) x
84.8
Fixed chassis system weights • Hardware only: 22.0 lbs. (10.0 kg) • Hardware only
25.0 lbs. (11.3 kg)
Fixed chassis system electrical power 100-127 V/200-240 V, 50/60 Hz
12/10 A
Temperature (ambient air) • Operating
41 °F to 104 °F (5 °C to 40 °C)
• Storage
-4 °F to 122 °F (-20 °C to 50 °C)
Humidity (ambient air) • Operating
5% to 85% RH, non-condensing
• Storage
5% to 85% RH, non-condensing
• UL 62368-1 / CSA C22.2 No.
62368-1
• ICES-003(A)/NMB-003(A)
• EN 55032 Class A, EN 55035, EN 61000-3-2, EN
61000-3-3
• AS/NZS CISPR
32, Class A
• KS C 9832 Class A, KS C
9835
• VCCI – CISPR
32, Class A
• RoHS Directive 2011/65/EU, Directive (EU)
2015/863
• WEEE Directive
2012/19/EU
最大值编号 chassis · single 测试 topology
The Metronome Timing System (942-0090) is used for synchronizing a total of eight or
Part Number 941-0132
941-0133
Interconnect and Network Performance
Tester 1600GE-C OSFP1600
2-Port
Performance Tester
1600GE-C
OSFP1600
2-Port Rackmount Chassis
Transmit engine Wire-speed packet generation with timestamps, sequence numbers, data integrity, and
Max. streams per port and 1600GE PAM4 speeds
• 2x800GE
64 (per fan-out)
• 4x400GE
64 (per fan-out)
• 8x200GE
64 (per fan-out)
• 1600GE, 800GE
400GE and 200GE PAM4 speeds:
• 64 bytes at full line rate
• 61 bytes at less than full line rate (approximately
90% utilization)
Maximum frame size for 1600GE PAM4 speeds
14,000 bytes
Maximum frame size in data center Ethernet
9,216 bytes for all speeds
Priority flow control (4:1) for
1600GE PAM4 speeds
• 4 line-rate-capable queues, each supporting up to 9,216-byte frame lengths
• 1 line-rate-capable queue, non-blocking supporting up to 9,216-byte frame length
Frame length controls Fixed, increment by user-defined step, weighted pairs (up to 16K for 1600GE/800GE and
up to 8K for lower speed), uniform, repeatable random, IMIX, and Quad Gaussian
User-Defined Fields (UDF)
• Fixed, counter (increment or decrement by user-defined step), value list, and random
条件:bit wide), or value list configurations (64-bit, 2x32-bit, 4x16-bit, or 4x8-bit wide).
• Up to 6 UDFs supporting fixed, nested counter, random configurations (32-bit or 2x16-
• Up to 4 additional UDFs supporting fixed, counter, random configurations (32-bit, or
2x16-bit wide).
• Split UDFs (for example
2x16 configuration) support different byte offset per UDF
Value lists (max.) per port for 1600GE PAM4 speeds
• 1x1600GE
64K / port /UDF
• 4x400GE
128K /2-port /UDF
• 8x200GE
128K / 4-ports /UDF
Sequence (max.) for 1600GE
PAM4 speeds
• 1x1600GE
16K / port /UDF
• 4x400GE:32K /port /UDF
• 8x200GE
32K / 2-ports /UDF
Error generation (FEC and standard Keysight L2/3
Ethernet in 1600GE PAM4
• FEC symbol error-injection allows the user to inject FEC symbol errors using various
weighted methods to achieve specific bit error rates (BER)
• Generate good CRC or force bad CRC, undersize and oversize standard Ethernet frame
Hardware checksum generation
Checksum generation for IPv4, IP over IP, ICMP/GRE/TCP/UDP, L2TP, GTP, and multilayer
checksum; support for protocol verification for control plane traffic
Link fault signaling for all speeds
• Reports, no fault, remote fault, and local fault port statistics
• Generate local and remote faults with controls for the number of faults and order of
• Option to have the transmit port ignore link faults from a remote link partner and send
Latency measurement resolution for 1600GE PAM4 speeds
• 800GE and 400GE
0.625 ns
Intrinsic latency compensation Removes inherent latency error from the port electronics for all speeds
Parts-per-million (ppm) (Planned) Ability to adjust the ppm line frequency: +/-
105 ppm on all the ports of the fixed
Part Number 941-0132
941-0133
Interconnect and Network Performance
Tester 1600GE-C OSFP1600
2-Port
Performance Tester
1600GE-C
OSFP1600
2-Port Rackmount Chassis
Receive engine Wire-speed packet filtering, capturing, real-time latency, and inter-arrival time for each
packet group, with data integrity, and sequence checking capability
Trackable receive flows per port without Sequence checking and with Tx/Rx synch for 1600GE PAM4 Ethernet
• 1600GE
16K full statistics
• 800GE, 400G, 200GE
32K full statistics
Tx/RX synch for 1600GE PAM4
• 1600GE
16K full statistics
• 800GE, 400G, 200GE
32K full statistics
Filters (user-defined statistics,
UDS) 2 SA/DA pattern matchers, 2x16-byte user-definable patterns. 6 UDS counters are available with offsets for start of frame
Hardware capture buffer 1 MB available per front panel OSFP1600 port and for the fan-out modes on that port
Link state, line speed, frames sent, valid frames received, bytes sent/received, fragments,
undersize, oversize, CRC errors, 6 user-defined stats, capture trigger (UDS
3), capture filter (UDS
4), data integrity frames, data integrity errors, sequence checking frames, sequence checking
errors, ARP, and PING requests and replies
FEC statistics for 1600GE
PAM4 Ethernet speeds
1600GE PAM4 speeds:
• FEC port statistics: Total Bit Errors, Max Symbol Errors, Corrected Codewords, Total
Codewords, Uncorrectable Codewords, Frame Loss Ratio, Pre-FEC Bit Error Rate, and
Codeword error distribution analysis
• FEC per lane Rx statistics: FEC Symbol Error Count, Corrected Bits Count, Symbol Error
Latency / jitter measurements Cut-through, store and forward, forwarding delay, latency/jitter, MEF jitter, and inter-
Receive-side PCS lanes port statistics counters for all speeds
PCS: Sync Errors, Illegal Codes, Remote Faults, Local Faults, Illegal Ordered Set, Illegal
PCS receive-side statistics and indicators for 1600GE PAM4
• Per-lane PCS receive capabilities include
• Receive — per-lane PCS receive statistics, Physical Lane assignments, Lane Marker
Lock, Lane Market Map, Relative Lane Skew, Lane Marker Error Count
• Receive — per-lane FEC receive statistics; FEC Symbol Error Count, FEC Corrected Bits
Advanced Rx Eye Histogram
Analysis (Planned) Advanced Rx Eye Histogram Analysis provides in-depth, user-selected, per lane
PAM4 signal shape histogram analysis, SER statistics, comparison of signal quality
between lanes and an array of eye closure measurements
Interconnect and Network Performance Tester
1600GE-C Chassis Models
IxExplorer: Layer 1-3 wire-speed traffic generation, capture, and analysis with Layer
1 BERT, Forward Error
Correction analysis and error injection with statistics, PCS Lanes Tx/Rx with statistics and reporting
capability. IxTcl API for custom user script development for Layer
1–3 testing using the IxExplorer features
IxNetwork: Wire-rate traffic generation with service modeling that builds realistic, dynamically controllable
data-plane traffic. IxNetwork offers the industry's best test solution for functional and performance testing
by using comprehensive emulation for routing, switching, MPLS, IP multicast, broadband, authentication,
Carrier Ethernet, and data center Ethernet protocols. Included with IxNetwork are test automation tools
based on TCL, Python, and the Rest/RestPy
Interconnect Test System Software: validates the functionality and performance of high-speed optical and
copper network equipment and interconnect media that use PAM4 signaling and Forward Error Correction
(FEC). It offers a first-of-its-kind, US patent pending Interconnect Library that introduces a new way to
organize, retrieve, and use interconnect data, including Common Management Interface Specification
条件:rackmount chassis with native OSFP1600 front panel ports and L1-3 testing support.
copper cables (DAC) that support 212.5Gb/s electrical lane speeds (942-1416).
Interconnect and Network Performance Tester
2-Port Hardware Chassis
941-0132
Interconnect and Network Performance Tester 1600GE-C, INPT-1600-C-2P-BT
2-port
benchtop chassis with native OSFP1600 front panel ports and L1-3 testing support. Includes
all 1x1600GE, 2x800GE, 4x400GE
8x200GE Ethernet speeds, ACC and DAC support
941-0133
Interconnect and Network Performance Tester 1600GE-C, INPT-1600-C-2P-RM
2-port half
Includes all 1x1600GE, 2x800GE, 4x400GE
8x200GE Ethernet speeds, ACC and DAC
UPG-INPT-1600GE-DAC, RETURN TO FACTORY system upgrade for the INPT-1600GE
benchtop chassis (941-0095) to replace the existing PHY PCBA hardware and add a new
PHY PCBA and required software to support Active Copper Cable (ACC) and passive
942-1417
UPG-INPT-1600GE-DAC, RETURN TO FACTORY system upgrade for the INPT-1600GE half-
rack chassis (941-0096) to replace the existing PHY PCBA hardware and add a new PHY
PCBA and required software to support Active Copper Cable (ACC) and passive copper
cables (DAC) that support
212.5Gb/s electrical lane speeds (942-1417).
930-3300
RoCEv2 Lossless Ethernet Enablement for Interconnect and Network Performance Tester
(930-3300); Perpetual node-locked license; Enable RoCEv2 capability for INPT-800-2P-
OSFP-BT 2-port benchtop with OSFP800 ports (941-0093), INPT-800-4P-OSFP-BT
4-port
benchtop with OSFP800 ports (941-0094), and INPT-1600-2P-BT
2-port benchtop chassis
with OSFP1600 ports (941-0095), and INPT-1600-2P-RM
2-port half-rack chassis with
OSFP1600 ports (941-0096); One option is required for each fixed chassis system
OSFP1600-DR-IHS-XCVR, OSFP1600-2xDR4
2x800GE pluggable optical transceiver with
Integrated Head Sink (IHS), SMF (single mode)
8x212Gb/s electrical lanes, Dual MPO-12 APC
connector, 500m reach. This optical transceiver is compatible with AresONE
1600GE
OSFP1600 with Integrated Head Sink (IHS) (941-0130), Interconnect and Network Performance
Tester 1600GE
2-port benchtop (941-0095) and Interconnect and Network Performance
Tester 1600GE
2-port half-rack chassis (941-0096).
It supports
2x800GE PAM4 signaling output (948-0130)
条件:IxNetwork Software Options 930-2250 IxNetwork Premium Package for Interconnect and Network Performance Tester; INCLUDES:
DR4-CBL
OSFP1600-DR-CBL, MPO12 Single Mode Female to Female, Type B fiber optic cable
2-meters
length. (942-3130). Compatible with OSFP1600-DR-IHS-XCVR (948-0130) and OSFP1600-DR-
RHS-XCVR (948-0131) dual connector optical transceivers (942-3130)
IxNetwork Base, RFC2544/2889/3918 QuickTest, and Protocol emulation for Routing,
Switching, MPLS/VPN, Carrier Ethernet and Timing, Data Center Ethernet, Broadband and
Authentication, SDN, and 5G Tra
以上指标摘自厂家官方数据手册,完整定义、测试条件与保证值口径以手册为准。完整指标、测试条件与定义口径请见产品页「软件和手册 | 白皮书」栏目中的官方数据手册。
是德科技 | KEYSIGHT · onetest 仪器资源库