ONETEST 欢迎您
厂商登录 | 入驻
登录 | 注册 购物车 微信公众号
客服
厂商登录
类似产品
• 频率范围：100kHz至26.5GHz•分析带宽：25MHz(40MHz可选）•量程：DANL~+27dBm•频率分辨率：0.001Hz•相位噪声： -106dBc/Hz@10kHz（CF=1GHz)•USB 控制，独立应用程序•可独立使用，方便外携•提供台式仪版本
2 Hz 至 67 GHz（可扩展至 110 GHz）· 最大分析带宽 1.2 GHz · 实时分析带宽 600 MHz
9 kHz 至 40 GHz 模块化矢量信号分析 · 分析带宽 300 MHz · 实时分析带宽 200 MHz
XA6系列SA6320A 67GHz 信号分析仪 8GHz|是德科技 (在产)
参考价格 ：
产品描述
详细指标
软件和手册|白皮书
购买渠道
选件
问大家
视频
测评
口碑
系统与解决方案
是德科技|KEYSIGHT
XA6 系列信号分析仪，67 GHz，最大分析带宽 8 GHz
台式信号与频谱分析仪
产品简介
Keysight Pro XA6 SA6320A 树立高性能信号分析新标准，将卓越性能与先进技术相结合，让您在需求不断变化时始终保持领先
核心参数
• 最大分析带宽：8 GHz
• 最高频率：67 GHz
• 实时频谱分析：否
功能特性
• 产品亮点
使用我们的 Pro XA6 SA6320A 信号分析仪，为 5G、雷达、电子战、卫星、脉冲无线电和下一代无线应用验证严苛的宽带和高频设计。
XA6 提供高达 8 GHz 分析带宽、高达 67 GHz 的频率覆盖、高动态范围、
低相位噪声和强大的 EVM 性能，帮助捕获复杂信号行为、揭示低电平损伤、减少重复测量，并自信地验证先进射频系统
测量信心
凭借同类最佳的 DANL、动态范围和相位噪声，揭示低电平和近距离损伤
高性能 EVM 凭借卓越的测量精度提升测试裕量
全面预选至 67 GHz，实现无杂散测量和可信结果
8 GHz 分析带宽和 80 MHz RBW 支持宽带分析和不断演进的标准
测量优化
凭借 GPU 加速实现快速的 5G NR EVM 解调速度
下一代基于 DDS 的本振实现出色的相位噪声性能
经过验证的测量科学，X 系列测量应用软件和 VSA 软件兼容传统 X 系列信号分析仪
全新 UI 体验通过高效工作流程优化任务
资源下载
以上内容与指标均取自是德科技（KEYSIGHT）官网该产品详情页与官方产品资料，未标注口径的为厂家公布值。
是德科技|KEYSIGHT · onetest 仪器资源库
是德科技 | KEYSIGHT
XA6系列SA6320A 67GHz 信号分析仪 8GHz 详细指标
Benchtop Signal and Spectrum Analyzers
一、频率与时间规格
| Frequency | Option | Frequency | Range |
|---|---|---|---|
| 555 | 2 Hz to 55 GHz | ||
| 567 | 2 Hz to 67 GHz |
Minimal Frequency
PA OFF
2 Hz
PA ON
100 kHz
Swept Spectrum Analysis (These Bands are Not Applicable to Wide-Bandwidth IQ Analysis)
Swept Frequency Band (RBW <
3 MHz, PA off)
本振倍频次数 (N) 频率范围
Direct (not using an LO for frequency conversion) N/A
2 Hz to 30 MHz
0 1
30 MHz to 3.6 GHz
1 2
3.5 to 8.2 GHz
2 1
8.1 to 11.5 GHz
3 2
11.4 to 23.47 GHz
3 3
23.37 to 34.5 GHz
4 3
34.4 to 36.4 GHz
4 4
36.3 to 48.52 GHz
4 6
48.42 to 53.5 GHz
5 6
53.4 to 67 GHz
频率参考
Accuracy (total) ± [(Initial accuracy) + (aging rate x time since last adjustment) +
老化率
Per day: ± 2 x
10-10
1st year: ± 2 x
10-8
2nd year: ± 1 x
10-8
10 years: ± 1 x
10-7
Temperature stability, full temperature range ± 2 x
10-9
Achievable initial calibration accuracy ± 5 x
10-9
Example frequency reference accuracy
1 year after last adjustment
= ± (5 ×10-9 + 2x 10-9 + 2 x
10-8)
= ± 2.7 x
10-8
残余调频
条件：≤ (0.25 Hz x N) p-p in 20 ms, nominal
Center frequency =
1 GHz
10 Hz RBW
10 Hz VBW
(N = 本振倍频次数, 见频段 table above)
Frequency Readout Accuracy (Start, Stop, Center, Marker) ± (marker frequency x frequency reference accuracy + 0.10 % x span + 5 % x RBW + 2 Hz +
0.5 x horizontal resolution) where horizontal resolution is Span/(Sweep Points-1)
标记频率计数器
Accuracy ± (marker frequency x frequency reference accuracy +
0.100 Hz)
Delta counter accuracy ± (delta frequency x frequency reference accuracy +
0.141 Hz)
Counter resolution
0.001 Hz
频率跨度 (FFT 和扫描模式)
Range 0 Hz (zero span)
10 Hz to maximum frequency of instrument
Resolution
2 Hz
精度 (标称值)
Stepped/Swept ± (0.1 % x span + horizontal resolution) where horizontal resolution is
span/(sweep points
-1)
FFT ± (0.1 % x span + horizontal resolution) where horizontal resolution is
span/(sweep points
-1)
扫描时间与触发
Range Span = 0 Hz
1 μs to 6000 s
Span ≥ 10 Hz
1 ms to 4000 s
条件：Span ≥ 10 Hz, swept ±0.01 % nominal
Span ≥ 10 Hz, FFT ±40 % nominal
Span = 0 Hz
±0.01 % nominal
触发延迟
Span = 0 Hz or FFT
–150 to +500 ms
Span ≥ 10 Hz, swept
0 to 500 ms
Resolution
0.1 μs
Gate methods Gated LO; gated video; gated FFT
条件：Gate delay jitter 33.3 ns p-p nominal
Gate length range (except method = FFT)
1 μs to 5.0 s
Gate delay range
0 to 100.0 s
扫描 (迹线) Point 范围
All spans
3 to 100,001
分辨率带宽 (RBW)
Range (with
–3.01 dB bandwidth)
1 Hz to 10 MHz (step resolution of 3 digits)
1 Hz to 40 MHz (step resolution of 3 digits; requires N90EMWR1B)
1 Hz to 80 MHz (step resolution of 3 digits; requires N90EMWR2B, IVL)
带宽精度 (功率)
条件：RBW Range Accuracy, Nominal 1 Hz to 100 kHz ± 0.005 dB
RBW Range Accuracy, Nominal 1 Hz to 1 MHz
> 100 kHz to 1 MHz (< 8.2 GHz center frequency)
± 0.007 dB
> 1 to 2 MHz (< 8.2 GHz center frequency)
± 0.019 dB
> 2 to 3 MHz (< 8.2 GHz center frequency)
± 0.032 dB
4, 5, 6, 8, 10 MHz (< 8.2 GHz center frequency)
± 0.009 dB
20, 28, 30, 40 MHz (> 50 MHz center frequency)
± 0.177 dB
50, 80 MHz (> 50 MHz center frequency)
± 0.424 dB
Bandwidth Accuracy (-3.01 dB)
≤ 8.2 GHz center frequency
± 0.35 %
> 8.2 GHz center frequency
± 0.55 %
> 1 to 3 MHz
± 1.19 %
4, 5, 6, 8, 10 MHz
± 0.42 %
20, 28, 30
40 MHz
> 50 MHz to 8.2 GHz center frequency
± 4.73 %
> 8.2 GHz center frequency
± 7.48 %
50
80 MHz
> 50 MHz to 8.2 GHz center frequency
± 14.2 %
> 8.2 GHz center frequency
± 20.2 %
Selectivity (-60 dB/-3 dB) < 5
1
预选器带宽
条件：Center Frequency Mean Bandwidth (-4 dB), Nominal
The preselector can have a significant passband ripple. To avoid ambiguous results, the
-4 dB bandwidth is characterized
10 GHz
53 MHz
15 GHz
53 MHz
20 GHz
53 MHz
25 GHz
54 MHz
30 GHz
55 MHz
35 GHz
56 MHz
40 GHz
57 MHz
45 GHz
60 MHz
50 GHz
61 MHz
55 GHz
64 MHz
60 GHz
69 MHz
65 GHz
74 MHz
67 GHz
78 MHz
视频带宽 (VBW) 滤波器
Range
1 Hz to 100 MHz
Accuracy
±6 %, nominal
检波方式
Normal, peak, sample, negative peak, log power average, RMS average, and voltage average
Free run Y Y
条件：Jitter up to ~10 ns p-p (nominal) External 2 Y Y Y
External
1 Y Y Y
External
3 Y Y Y
ADC Y
Similar to Video, but operates digitally on mag[I,Q], prior to decimation, filtering, and corrections
Periodic Y Y Y
Repetitive “frame” trigger, at precise interval, following an External or RF
电平) 规格补充信息
Minimum settable level
-170 dBm Useful range limited by noise
扫描类型 = 扫描
Detector = Normal, Peak, Sample or Negative peak Triggers on the signal before detection, which is similar to the
displayed signal
Detector = Average Triggers on the signal before detection, but with a single-pole filter
added to give similar smoothing to that of the average detector
Sweep type = FFT Triggers on the signal envelope in a bandwidth wider than the FFT
规格补充信息
Level range
−40 to −10 dBm plus
衰减 (标称值)
Noise will limit trigger level range at high frequencies, such as above
15 GHz
电平精度
条件：With positive slope trigger. Trigger level with negative slope is nominally 1 to 4 dB lower than positive slope.
Absolute ±2 dB + absolute amplitude accuracy (nominal)
Relative
±2 dB (nominal)
二、幅度精度与量程规格
Amplitude characteristics vary by user-selectable front-end path. Swept SA measurements are
normally made with the preselector on (in circuit). These settings impact amplitude accuracy and
Gain Adjust Description
Front End Settings for Frequencies ≤
8.2 GHz
Off Off
条件：Settings provide best dynamic range and lowest internally-generated distortion.
Default instrument state following power-on, boot-up, or PRESET.
Suitable for harmonics, IMD, spurious in presence of large signals, etc. unless
Off Enabled
Settings provide lower DANL at frequencies below
8.2 GHz, compared to
设置 provide 下限 DANL（含） degradation 至失真
Suitable for measurements near the noise floor when large, out-of-band signals
Requires P55, P5N, P67 or P6N.
Settings provide better DANL compared to PA Off, while preserving very good
动态范围
Suitable for distortion measurements (harmonics, IMD, etc.) when a lower noise
floor is needed
Specified down to 100 kHz
Requires P55, P5N, P67 or P6N.
Settings provide best DANL, compared to PA Low
条件：Best for finding low-level spurs, oscillations, etc. near the noise floor.
Specified down to 100 kHz.
Frontend Settings for Frequencies >
8.2 GHz
Not applicable for frequencies
条件：Settings provide best dynamic range and lowest internally-generated distortion.
> 8.2 GHz
Default instrument state following power-on, boot-up, or PRESET.
Suitable for harmonics, IMD, spurious in presence of large signals, etc. unless
标配低
Requires P55, P5N, P67 or P6N.
Settings provide better DANL compared to PA Off, while preserving very good
动态范围
Suitable for distortion measurements (harmonics, IMD, etc.) when a lower noise
floor is needed
Specified down to 100 kHz
标配高
Requires P55, P5N, P67 or P6N.
Settings provide best DANL, compared to PA Low
条件：Best for finding low-level spurs, oscillations, etc. near the noise floor.
Specified down to 100 kHz.
Bypasses preselector
Settings provide very good wideband digitizer measurements at mid-high input
Bypasses preselector
Requires P55, P5N, P67 or P6N.
MPB allows wideband measurements, provides better DANL and preserves
动态范围
Settings provide good wideband digitizer measurements at low input power
region with very low distortion. Good for FFT measurements and wideband
Bypasses preselector
Requires P55, P5N, P67 or P6N.
MPB allows wideband measurements, provides best DANL and preserves
动态范围
Settings provide good wideband digitizer measurements at very low input
power region with low distortion. Good for FFT measurements and wideband
digitizer measurements, especially EVM at very low input power.
DATA SHEET
Measurement range Displayed average noise level (DANL) to maximum
safe 输入电平
Input attenuator range (2 Hz to 67 GHz)
0 to 75 dB in 1 dB steps
5 dB steps in Direct path with PA Off
最大安全输入电平 (最大 Applied 至 RF 输入连接器)
Average total power (with and without preamp) +26 dBm (0.4 W)
0 dB input attenuation
+30 dBm (1 W), PA off, ≥
10 dB input attenuation
Peak pulse power (< 10 μs pulse width, < 1 % duty cycle, and input attenuation ≥ 30 dB)
+50 dBm (100 W)
DC Volts
DC coupled
± 0.2 Vdc
显示范围
Log scale
0.1 to 1 dB/division in 0.1 dB steps
1 to 20 dB/division in 1 dB steps (10 display)
Linear scale
10 divisions
频率响应
条件：Note: Frequency response specifications are given as absolute amplitude accuracy.
Standard Path Frequency Response (Swept, Preselector ON, PA OFF)
10 dB Input Attenuation, RBW ≤ 3 MHz, Preselector Centering Applied Above
8.2 GHz
Frequency Full Range
20 to 30 °C Typical
9 kHz to 30 MHz ±1.16 dB ±1.05 dB
±0.39 dB
> 30 to 50 MHz ±0.86 dB ±0.78 dB
±0.26 dB
> 50 to 125 MHz ±0.85 dB ±0.76 dB
±0.28 dB
> 125 MHz to 3.6 GHz ±0.83 dB ±0.65 dB
±0.27 dB
> 3.6 to 5.65 GHz ±0.79 dB ±0.72 dB
±0.22 dB
> 5.65 to 8.2 GHz ±0.89 dB ±0.78 dB
±0.27 dB
> 8.2 to 9.5 GHz ±2.74 dB ±2.05 dB
±0.85 dB
> 9.5 to 11.47 GHz ±1.67 dB ±1.36 dB
±0.44 dB
> 11.47 to 34.5 GHz ±1.96 dB ±1.7 dB
±0.49 dB
> 34.5 to 53.5 GHz ±2.41 dB ±2.04 dB
±0.64 dB
> 53.5 to 55 GHz ±2.15 dB ±1.89 dB
±0.54 dB
> 55 to 59 GHz ±2.55 dB ±2.25 dB
±0.65 dB
> 59 to 66 GHz ±3.39 dB ±2.7 dB
±0.85 dB
> 66 to 67 GHz ±3.89 dB ±3.2 dB
±0.85 dB
Standard Path Frequency Response (Swept, Preselector ON, PA Low)
10 dB input Attenuation, RBW ≤ 3 MHz, Preselector Centering Applied Above
8.2 GHz
Frequency Full Range
20 to 30 °C Typical
100 to 300 kHz ±2.45 dB ±1.79 dB
±0.69 dB
> 300 kHz to 1 MHz ±1.4 dB ±1.2 dB
±0.22 dB
> 1 to 30 MHz ±1.04 dB ±0.96 dB
±0.54 dB
> 30 to 50 MHz ±0.99 dB ±0.89 dB
±0.31 dB
> 50 to 125 MHz ±0.92 dB ±0.8 dB
±0.33 dB
> 125 to 3.6 GHz ±0.91 dB ±0.72 dB
±0.30 dB
> 3.6 to 5.65 GHz ±0.9 dB ±0.78 dB
±0.36 dB
> 5.65 to 8.2 GHz ±0.84 dB ±0.7 dB
±0.34 dB
> 8.2 to 9.5 GHz ±2.82 dB ±2.03 dB
±1.08 dB
> 9.5 to 11.48 GHz ±2.3 dB ±1.94 dB
±0.78 dB
> 11.48 to 15.5 GHz ±2.49 dB ±1.97 dB
±0.73 dB
> 15.5 to 34.5 GHz ±2.36 dB ±2.04 dB
±0.87 dB
> 34.5 to 53.5 GHz ±2.8 dB ±2.38 dB
±0.81 dB
> 53.5 to 55 GHz ±2.28 dB ±2.08 dB
±0.65 dB
> 55 to 59 GHz ±3.2 dB ±2.8 dB
±0.90 dB
> 59 to 66 GHz ±3.95 dB ±3.42 dB
±1.22 dB
> 66 to 67 GHz ±4.04 dB ±3.5 dB
±1.03 dB
Standard Path Frequency Response (Swept, Preselector ON, PA High)
10 dB Input Attenuation, RBW ≤ 3 MHz, Preselector Centering Applied Above
8.2 GHz
Frequency Full Range
20 to 30 °C Typical
100 to 300 kHz ±2.38 dB ±1.93 dB
±0.68 dB
> 300 kHz to 1 MHz ±1.37 dB ±1.25 dB
±0.22 dB
> 1 to 30 MHz ±1.01 dB ±0.92 dB
±0.60 dB
> 30 to 50 MHz ±0.98 dB ±0.88 dB
±0.30 dB
> 50 to 125 MHz ±0.88 dB ±0.80 dB
±0.29 dB
> 125 to 3.6 GHz ±0.90 dB ±0.70 dB
±0.25 dB
> 3.6 to 5.65 GHz ±1.01 dB ±0.91 dB
±0.37 dB
> 5.65 to 8.2 GHz ±0.95 dB ±0.82 dB
±0.35 dB
> 8.2 to 9.5 GHz ±3.09 dB ±2.28 dB
±1.59 dB
> 9.5 to 11.48 GHz ±2.48 dB ±2.05 dB
±1.04 dB
> 11.48 to 15.5 GHz ±1.92 dB ±1.72 dB
±0.50 dB
> 15.5 to 34.5 GHz ±2.54 dB ±2.20 dB
±0.73 dB
> 34.5 to 53.5 GHz ±3.42 dB ±2.90 dB
±1.02 dB
> 53.5 to 55 GHz ±2.60 dB ±2.24 dB
±0.74 dB
> 55 to 59 GHz ±4.41 dB ±3.57 dB
±1.42 dB
DATA SHEET
条件：MPB Path Frequency Response (Swept, Preselector Off, PA ON) 10 dB Input Attenuation, RBW ≤ 3 MHz, Nominal
> 59 to 66 GHz ±4.70 dB ±4.07 dB
±1.49 dB
> 66 to 67 GHz ±4.71 dB ±3.87 dB
±1.34 dB
Standard Path Frequency Response (Swept, Preselector ON, Allow RF Gain Adjust Enabled)
0 dB Input Attenuation, RBW ≤ 3 MHz, Preselector Centering Applied Above
8.2 GHz
Frequency Full Range
20 to 30 °C Typical
2 to 50 MHz ±1.09 dB ±0.97 dB
±0.34 dB
> 50 to 125 MHz ±0.90 dB ±0.80 dB
±0.29 dB
> 125 to 3.6 GHz ±1.02 dB ±0.90 dB
±0.34 dB
> 3.6 to 5.65 GHz ±1.42 dB ±1.02 dB
±0.51 dB
> 5.65 to 8.2 GHz ±0.99 dB ±0.86 dB
±0.36 dB
MPB Path Frequency Response (Swept, Preselector ON, PA OFF) 0 dB Input Attenuation, RBW ≤
3 MHz
Frequency Full Range
20 to 30 °C Typical
8.2 to 11.47 GHz ±1.34 dB ±1.18 dB
±0.33 dB
> 11.47 to 34.5 GHz ±2.08 dB ±1.74 dB
±0.52 dB
> 34.5 to 53.5 GHz ±2.22 dB ±1.88 dB
±0.59 dB
> 53.5 to 55 GHz ±2.15 dB ±1.89 dB
±0.54 dB
> 55 to 59 GHz ±2.58 dB ±2.25 dB
±0.72 dB
> 59 to 66 GHz ±3.01 dB ±2.56 dB
±0.78 dB
> 66 to 67 GHz ±3.41 dB ±2.96 dB
±0.73 dB
Frequency PA Low PA High 8.2 to 11.48 GHz ±0.27 dB
± 0.27 dB
> 11.48 to 15.5 GHz ±0.23 dB
± 0.22 dB
> 15.5 to 34.5 GHz ±0.4 dB
± 0.38 dB
> 34.5 to 53.5 GHz ±0.37 dB
± 0.49 dB
> 53.5 to 67 GHz ±0.5 dB
± 0.68 dB
标配通路频率响应 (扫描, Preselector 开)
条件：RBW > 3 MHz, Preselector Centering Applied Above 8.2 GHz, Nominal
Frequency PA Off
10 dB
输入衰减
PA Low
10 dB
输入衰减
PA High
10 dB
输入衰减
RF Gain Adjust Enabled
0 dB
Input Attenuation 260 MHz to 3.6 GHz ±0.11 dB ±0.15 dB ±0.13 dB
±0.19 dB
> 3.6 to 5.4 GHz ±0.12 dB ±0.20 dB ±0.21 dB
±0.21 dB
> 5.4 to 8.2 GHz ±0.14 dB ±0.16 dB ±0.19 dB
±0.20 dB
> 8.2 to 12.1 GHz ±0.27 dB ±0.38 dB
±0.42 dB
> 12.1 to 15.2 GHz ±0.22 dB ±0.22 dB
±0.22 dB
> 15.2 to 37.1 GHz ±0.22 dB ±0.44 dB
±0.43 dB
> 37.1 to 53.1 GHz ±0.36 dB ±0.42 dB
±0.47 dB
> 53.1 to 67 GHz ±0.39 dB ±0.49 dB
±0.65 dB
MPB 通路频率响应 (扫描, Preselector 关)
RBW >
3 MHz, Nominal
Frequency PA Off
0 dB Input
PA Low, 10 dB Input Attenuation PA High
10 dB Input Attenuation
8.2 to 12.1 GHz ±0.15 dB ±0.29 dB
±0.28 dB
> 12.1 to 15.2 GHz ±0.22 dB ±0.22 dB
±0.20 dB
> 15.2 to 37.1 GHz ±0.22 dB ±0.44 dB
±0.42 dB
> 37.1 to 53.1 GHz ±0.27 dB ±0.35 dB
±0.48 dB
> 53.1 to 67 GHz ±0.34 dB ±0.55 dB
±0.59 dB
MPB 通路 IF 频率响应 (Preselector 关, PA OFF)
条件：Center Frequency Span Amplitude Max Error, Nominal Amplitude RMS, Nominal
10 to 50 MHz ≤ 10 MHz ±0.09 dB
0.04 dB
> 50 MHz to 3.6 GHz ≤ 10 MHz ±0.11 dB
0.04 dB
> 3.6 to 5.65 GHz ≤ 10 MHz ±0.08 dB
0.03 dB
> 5.65 to 11.47 GHz ≤ 10 MHz ±0.06 dB
0.02 dB
DATA SHEET
条件：attenuation, 900 Hz to 3.6 GHz 2.34:1 (nominal)
the details, such as the frequencies of the peaks and valleys, will shift.
> 11.47 to 34.5 GHz ≤ 10 MHz ±0.07 dB
0.02 dB
> 34.5 to 53.5 GHz ≤ 10 MHz ±0.12 dB
0.04 dB
> 53.5 to 55 GHz ≤ 10 MHz ±0.07 dB
0.02 dB
> 55 to 66 GHz ≤ 10 MHz ±0.05 dB
0.02 dB
> 66 to 67 GHz ≤ 10 MHz ±0.06 dB
0.02 dB
Attenuator Switching Uncertainty (Relative to 10 dB Reference Setting)
Attenuation >
2 dB, Nominal
Frequency 9 kHz to 30 MHz
± 0.25 dB
> 30 MHz to 67 GHz
± 0.40 dB, PA Off
± 0.50 dB, PA On
VSWR (Voltage Standing Wave Ratio) at RF Input (95th Percentile, Unless Stated Otherwise)
Standard path
0 dB input
Center Frequency STD (10 dB Input Attenuation)
STD, PA Low/High (0 dB Input Attenuation)
STD, RF Gain Adjust Enabled (0 dB Input Attenuation) 900 Hz to 30 MHz
1.08
> 30 MHz to 3.6 GHz 1.19 1.58
1.22
> 3.6 to 8.2 GHz 1.12 1.22
1.15
> 8.2 to 11.5 GHz 1.16
1.27
> 11.5 to 20 GHz 1.17
1.32
> 20 to 30 GHz 1.26
1.68
> 30 to 44 GHz 1.33
1.74
> 44 to 53.5 GHz 1.74
1.91
> 53.5 to 67 GHz 1.70
2.05
The magnitude of the mismatch over the range of frequencies will be very similar between MPB and non-MPB operation, but
VSWR Plots
Figure 1. VSWR vs. frequency (0 to 3.6 GHz), standard path, PA off, 10 dB attenuation, measured on
3 units
Figure 2. VSWR vs. frequency (3.6 to 20 GHz), standard path, PA off, 10 dB attenuation, measured on
3 units
DATA SHEET
Figure 3. VSWR vs. frequency (20 to 44 GHz), standard path, PA off, 10 dB attenuation, measured on
3 units
Figure 4. VSWR vs. frequency (44 to 67 GHz), standard path, PA off, 10 dB attenuation, measured
3 units
DATA SHEET
Figure 5. VSWR vs. frequency (0 to 3.6 GHz), standard path, PA Low/High, 0 dB attenuation, measured on
3
Figure 6. VSWR vs. frequency (3.6 to 20 GHz), standard path, PA Low/High, 0 dB attenuation, measured on
3
DATA SHEET
Figure 7. VSWR vs. frequency (20 to 44 GHz), standard path, PA Low/High, 0 dB attenuation, measured on
3
Figure 8. VSWR vs. frequency (44 to 67 GHz), standard path, PA Low/High, 0 dB attenuation, measured on
3
DATA SHEET
Figure 9. VSWR vs. frequency (30 MHz to 8.2 GHz), standard path, RF Gain Adjust enabled
0 dB attenuation
measured on
3 units
DATA SHEET
条件：Resolution Bandwidth Switching Uncertainty (Relative to 30 kHz RBW), Nominal
1 Hz to 27 kHz
± 0.06 dB
> 27 kHz to 91 kHz
± 0.01 dB
> 91 kHz to 910 kHz
± 0.02 dB
> 910 kHz to 3 MHz
± 0.03 dB
4, 5, 6, 8, 10 MHz
± 0.10 dB
20, 28, 30, 40 MHz
± 0.16 dB; requires Option N90EMWR1B or N90EMWR2B
50, 80 MHz
± 0.23 dB; requires Option N90EMWR2B
Log scale
–170 to +30 dBm in 0.01 dB steps
Linear scale
707 pV to 7.07 V with 0.11 % (0.01 dB) resolution
Accuracy (Only affects the display, not the measurement, so it causes no additional error in measurement results from trace data or markers.)
0 dB
显示刻度 Switching 不确定度
Switching between linear and log (Only affects the display, not the measurement, so it causes no additional error in measurement results from trace data or markers.)
0 dB
Log scale/div switching (Only affects the display, not the measurement, so it causes no additional error in measurement results from trace data or markers.)
0 dB
Low Gain High Gain
条件：Noise figure DANL + 176.25 dB (nominal)
Gain 15 dB (nominal) 25 dB (nominal)
Option P55/P5N 100 kHz to 55 GHz
100 kHz to 55 GHz
Option P67/P6N 100 kHz to 67 GHz
100 kHz to 67 GHz
三、动态范围规格
1 dB Gain Compression
条件：how large an interfering signal must be in order to cause a 1 dB change in an on-screen signal.
spacings, ADC clipping may occur at a level lower than the 1 dB compression point.
measurement results can change with RL changes when the input attenuation is set to auto.
• Mixer power level (dBm) = total power at the input (dBm) − input attenuation (dB).
Standard Path 1 dB Gain Compression (Swept, Preselector ON), Nominal
• Large signals, even at frequencies not shown on the screen, can cause the analyzer to
mismeasure on-screen signals because of two-tone gain compression. This specification tells
• Specified at 1 kHz RBW with 100 kHz tone spacing. The compression point will nominally equal
the specification for tone spacing greater than
5 times the prefilter bandwidth. At smaller
• Reference level and off-screen performance: The Reference Level (RL) behavior differs from
some earlier analyzers in a way that makes this analyzer more flexible. In other analyzers, the
RL controlled how the measurement was performed as well as how it was displayed. Because
the logarithmic amplifier in these analyzers had both range and resolution limitations, this
behavior was necessary for optimum measurement accuracy. The logarithmic amplifier in this
signal analyzer, however, is implemented digitally such that the range and resolution greatly
exceed other instrument limitations. Because of this, the analyzer can make measurements
largely independent of the setting of the RL without compromising accuracy. Because the RL
becomes a display function, not a measurement function, a marker can read out results that
are off-screen, either above or below, without any change in accuracy. The only exception to
the independence of RL and the way in which the measurement is performed is in the input
attenuation setting: When the input attenuation is set to auto, the rules for the determination of
the input attenuation include dependence on the reference level. Because the input
attenuation setting controls the tradeoff between large signal behaviors (third-order
intermodulation, compression, and display scale fidelity) and small signal effects (noise), the
• Total power at the preamp (dBm) = total power at the input (dBm) − input attenuation (dB),
when input attenuation ≤
15 dB
• Total power at the preamp (dBm) = total power at the input (dBm) – 15 (dB), when input
attenuation >
15 dB
Center Frequency PA Off PA Low PA High 30 to 100 MHz +6 dBm -10 dBm
-16 dBm
> 100 MHz to 8.2 GHz +7 dBm -9 dBm
-15 dBm
> 8.2 to 67 GHz +7 dBm -7 dBm
-15 dBm
IF Prefilter Bandwidth
条件：RBW, Zero Span or Swept FFT Width, Sweep Type = FFT –3 dB Bandwidth (Nominal)
This table applies for sweep rates ≤ 1.1 times RBW-squared, RBW shapes that are Gaussian, FlatTop or Custom and for
the non-Direct signal path. Otherwise, compute an "effective RBW" = 1.1 * span / (sweep time × RBW). To determine the
IF Prefilter bandwidth, look up this effective RBW in the table instead of the actual RBW. For example, for RBW =
3 kHz
Span = 300 kHz, and sweep time = 42 ms, the sweep rate = 7.1 MHz/s, while RBW-squared is
9 MHz/s. So, the sweep
rate is < 1.1 times RBW-squared and the table applies; row 1 shows the IF prefilter bandwidth is nominally
10 kHz. If the
sweep time is
1 ms, then the effective RBW computes to 100 kHz. This would result in an IF prefilter bandwidth from the
third row, nominally
10 MHz.
≤ 4.01 kHz < 4.01 kHz
10 kHz
> 4.01 to 28.8 kHz < 28.81 kHz
80 kHz
> 28.8 kHz to 3 MHz < 10 MHz
10 MHz
< 40 MHz
40 MHz
> 3 to 80 MHz < 480 MHz
480 MHz
平均显示噪声电平 (DANL)
Input terminated, Sample or Average detector, Averaging type set to Log, IF Gain = High
30 kHz
Resolution Bandwidth normalized to 1 Hz
0 dB input attenuation, NFE off
标配通路 (扫描, Preselector ON, PA OFF)
Noise Floor Extension (Option NF2) nominally improves DANL by
7 to 11 dB
Frequency RBW ≤
3 MHz
Full Range
RBW ≤
3 MHz
20 to 30 °C
RBW ≤
3 MHz
Otherwise Stated
条件：2 Hz to 9 kHz -113 dBm (nominal)
> 9 to 25 kHz -121 dBm (nominal)
> 25 to 100 kHz -149 dBm (nominal)
RBW >
3 MHz, Nominal
> 100 kHz to 3 MHz -142 dBm -143 dBm
-150 dBm
> 3 to 30 MHz -154 dBm -154 dBm -157 dBm
-157 dBm
> 30 MHz to 1 GHz -154 dBm -154 dBm -156 dBm
-157 dBm
> 1 to 1.8 GHz -152 dBm -153 dBm -155 dBm
-156 dBm
> 1.8 to 3.6 GHz -150 dBm -151 dBm -153 dBm
-155 dBm
> 3.6 to 6 GHz -153 dBm -153 dBm -156 dBm
-158 dBm
> 6 to 8 GHz -151 dBm -152 dBm -154 dBm
-156 dBm
> 8 to 9 GHz -145 dBm -146 dBm -150 dBm
-153 dBm
> 9 to 12 GHz -147 dBm -148 dBm -151 dBm
-153 dBm
> 12 to 18 GHz -150 dBm -151 dBm -154 dBm
-156 dBm
> 18 to 26 GHz -147 dBm -148 dBm -152 dBm
-154 dBm
> 26 to 34.5 GHz -143 dBm -144 dBm -148 dBm
-151 dBm
> 34.5 to 37 GHz -145 dBm -146 dBm -149 dBm
-148 dBm
> 37 to 41 GHz -144 dBm -144 dBm -148 dBm
-150 dBm
> 41 to 44 GHz -143 dBm -143 dBm -147 dBm
-149 dBm
> 44 to 52 GHz -140 dBm -141 dBm -144 dBm
-148 dBm
> 52 to 55 GHz -137 dBm -137 dBm -142 dBm
-145 dBm
> 55 to 57 GHz -135 dBm -136 dBm -140 dBm
-144 dBm
> 57 to 60 GHz -136 dBm -136 dBm -141 dBm
-144 dBm
> 60 to 65 GHz -133 dBm -133 dBm -138 dBm
-142 dBm
> 65 to 67 GHz -130 dBm -131 dBm -136 dBm
-139 dBm
Standard path (Swept, Preselector ON, PA High, Option P55/P67)
Noise Floor Extension (Option NF2) nominally improves DANL by
5 to 9 dB
Frequency RBW ≤
3 MHz
Full Range
条件：Nominal 100 kHz to 1 MHz -120 dBm -122 dBm -127 dBm
RBW ≤
3 MHz
20 to 30 °C RBW ≤ 3 MHz, Typical RBW >
3 MHz
DATA SHEET
> 1 to 3 MHz -147 dBm -148 dBm
-151 dBm
> 3 to 9 MHz -150 dBm -150 dBm
-153 dBm
> 9 to 30 MHz -154 dBm -154 dBm
-157 dBm
> 30 to 300 MHz -158 dBm -158 dBm -161 dBm
-165 dBm
> 300 MHz to 2.1 GHz
-165 dBm -165 dBm -168 dBm
-168 dBm
> 2.1 to 8 GHz -165 dBm -165 dBm -167 dBm
-169 dBm
> 8 to 17 GHz -163 dBm -163 dBm -166 dBm
-167 dBm
> 17 to 22 GHz -162 dBm -162 dBm -165 dBm
-166 dBm
> 22 to 27 GHz -161 dBm -161 dBm -164 dBm
-166 dBm
> 27 to 32 GHz -160 dBm -160 dBm -163 dBm
-164 dBm
> 32 to 43 GHz -159 dBm -159 dBm -162 dBm
-164 dBm
> 43 to 52 GHz -156 dBm -157 dBm -160 dBm
-162 dBm
> 52 to 56 GHz -155 dBm -156 dBm -159 dBm
-161 dBm
> 56 to 59 GHz -154 dBm -155 dBm -158 dBm
-160 dBm
> 59 to 62 GHz -152 dBm -153 dBm -156 dBm
-159 dBm
> 62 to 63 GHz -151 dBm -152 dBm -156 dBm
-158 dBm
> 63 to 64 GHz -149 dBm -150 dBm -154 dBm
-157 dBm
> 64 to 67 GHz -146 dBm -148 dBm -152 dBm
-156 dBm
Standard path (Swept, Preselector ON, PA High, Option P5N/P6N)
Frequency RBW ≤
3 MHz
Full Range
条件：Nominal 100 kHz to 43.4 GHz Refer to standard path DANL for Option P55/P67
RBW ≤
3 MHz
20 to 30 °C
RBW ≤ 3 MHz, Typical RBW >
3 MHz
>43.4 to 52 GHz -139 dBm -140 dBm -145 dBm
-147 dBm
>52 to 53.5 GHz -135 dBm -136 dBm -142 dBm
-147 dBm
>53.5 to 56 GHz -141 dBm -141 dBm -146 dBm
-147 dBm
>56 to 59 GHz -138 dBm -138 dBm -144 dBm
-146 dBm
>59 to 62 GHz -132 dBm -132 dBm -139 dBm
-142 dBm
>62 to 64 GHz -130 dBm -130 dBm -136 dBm
-138 dBm
>64 to 67 GHz -126 dBm -126 dBm -133 dBm
-136 dBm
Standard path (Swept, Preselector ON, RF Gain Adjust Enabled)
Frequency RBW ≤
3 MHz
Full Range
条件：Nominal 13 to 33 MHz -146 dBm -146 dBm -149 dBm -154 dBm
RBW ≤
3 MHz
20 to 30 °C
RBW ≤ 3 MHz, Typical RBW >
3 MHz
> 33 to 53 MHz -150 dBm -150 dBm -153 dBm
-155 dBm
> 53 to 200 MHz -152 dBm -152 dBm -155 dBm
-157 dBm
> 200 MHz to 7 GHz -155 dBm -156 dBm -158 dBm
-160 dBm
> 7 to 8.2 GHz -155 dBm -155 dBm -158 dBm
-159 dBm
MPB 通路 (扫描, PA OFF)
Noise Floor Extension (Option NF2) nominally improves DANL by
7 to 10 dB
Frequency RBW ≤
3 MHz
Full Range
RBW ≤
3 MHz
20 to 30 °C
RBW ≤ 3 MHz, Typical RBW >
3 MHz
> 8.1 to 10 GHz -153 dBm -154 dBm -156 dBm
-158 dBm
> 10 to 11.5 GHz -152 dBm -152 dBm -155 dBm
-157 dBm
> 11.5 to 15 GHz -153 dBm -153 dBm -156 dBm
-158 dBm
> 15 to 18 GHz -151 dBm -151 dBm -154 dBm
-156 dBm
> 18 to 21 GHz -148 dBm -148 dBm -152 dBm
-154 dBm
> 21 to 27 GHz -145 dBm -145 dBm -149 dBm
-153 dBm
> 27 to 30 GHz -142 dBm -143 dBm -147 dBm
-150 dBm
> 30 to 34.5 GHz -141 dBm -141 dBm -145 dBm
-148 dBm
> 34.5 to 41 GHz -146 dBm -146 dBm -150 dBm
-153 dBm
> 41 to 44 GHz -145 dBm -145 dBm -150 dBm
-152 dBm
> 44 to 45 GHz -143 dBm -143 dBm -149 dBm
-151 dBm
> 45 to 47 GHz -145 dBm -145 dBm -149 dBm
-150 dBm
> 47 to 49 GHz -144 dBm -144 dBm -148 dBm
-150 dBm
> 49 to 50 GHz -139 dBm -140 dBm -146 dBm
-150 dBm
> 50 to 52 GHz -143 dBm -143 dBm -147 dBm
-149 dBm
> 52 to 54 GHz -139 dBm -140 dBm -145 dBm
-148 dBm
> 54 to 57 GHz -139 dBm -139 dBm -144 dBm
-147 dBm
> 57 to 62 GHz -136 dBm -136 dBm -143 dBm
-146 dBm
> 62 to 67 GHz -138 dBm -138 dBm -142 dBm
-145 dBm
MPB path (Swept, PA High, Option P55/P67)
DATA SHEET
Noise Floor Extension (Option NF2) Nominally Improves DANL by
5 to 7 dB
Frequency RBW ≤
3 MHz
Full Range
条件：Nominal 8.1 to 11.5 GHz -161 dBm -162 dBm -165 dBm -165 dBm
RBW ≤
3 MHz
20 to 30 °C
RBW ≤ 3 MHz, Typical RBW >
3 MHz
> 11.5 to 18 GHz -162 dBm -163 dBm -166 dBm
-167 dBm
> 18 to 26 GHz -162 dBm -162 dBm -164 dBm
-165 dBm
> 26 to 29 GHz -159 dBm -160 dBm -163 dBm
-164 dBm
> 29 to 32 GHz -159 dBm -159 dBm -162 dBm
-163 dBm
> 32 to 42 GHz -156 dBm -156 dBm -159 dBm
-159 dBm
> 42 to 48 GHz -154 dBm -155 dBm -158 dBm
-159 dBm
> 48 to 51 GHz -155 dBm -155 dBm -158 dBm
-159 dBm
> 51 to 60 GHz -153 dBm -153 dBm -157 dBm
-157 dBm
> 60 to 63 GHz -151 dBm -151 dBm -155 dBm
-156 dBm
> 63 to 67 GHz -150 dBm -150 dBm -154 dBm
-155 dBm
MPB path (Swept, PA High, Option P5N/P6N)
Frequency RBW ≤
3 MHz
Full Range
条件：Nominal 8.1 to 43.4 GHz Refer to MPB path DANL for Option P55/P67
RBW ≤
3 MHz
20 to 30 °C
RBW ≤ 3 MHz, Typical RBW >
3 MHz
>43.4 to 48GHz -142 dBm -142 dBm -146 dBm
-148 dBm
>48 to 53GHz -141 dBm -141 dBm -145 dBm
-146 dBm
>53 to 54GHz -141 dBm -142 dBm -145 dBm
-146 dBm
>54 to 59GHz -141 dBm -141 dBm -145 dBm
-146 dBm
>59 to 61GHz -137 dBm -137 dBm -142 dBm
-144 dBm
>61 to 64GHz -135 dBm -135 dBm -140 dBm
-141 dBm
>64 to 67GHz -132 dBm -132 dBm -137 dBm
-140 dBm
Residuals, Images, and Spurious Responses
条件：Zero span or FFT -100 dBm (nominal)
Residual Responses (Input Terminated
0 dB Attenuation)
400 kHz to 67 GHz (swept)
-100 dBm
频率标称值
-10 dBm
≤ 67 GHz f+45 MHz
-90 dBc
≤ 8.2 GHz f+1045 MHz
-80 dBc
> 8.2 to 11.5 GHz f+1045 MHz
-70 dBc
> 11.5 to 34.5 GHz f+1045 MHz
-75 dBc
> 34.5 to 53.5 GHz f+1045 MHz
-70 dBc
> 53.5 to 67 GHz f+1045 MHz
-64 dBc
Other Spurious Responses (Input-Related, Standard Path, PA OFF)
Performance is nominally the same, with PA on. N is the LO multiplication factor. Refer to earlier table for the N value
Mixer 电平 Response, 标称值
条件：Nominally –40 dBc under large magnetic (0.38 Gauss rms) or vibrational (0.21 g rms) environmental stimuli.
First RF order (f ≥
10 MHz from carrier) Including IF Feedthrough, LO Harmonic Mixing Responses
Carrier frequency ≤ 3 GHz -10 dBm
-80 dBc
3 GHz < Carrier frequency ≤ 4.1 GHz -10 dBm
-54 dBc
4.1 < Carrier frequency ≤ 12 GHz -10 dBm
-95 dBc
Carrier frequency > 12 GHz -10 dBm
-100 dBc
Higher RF Order (f ≥
10 MHz from Carrier)
Carrier frequency ≤ 11.5 GHz -30 dBm
-85 dBc
11.5 < Carrier frequency ≤ 53.4 GHz -30 dBm
-95 dBc
53.4 < Carrier frequency ≤ 67 GHz -30 dBm
-85 dBc
LO-Related Spurious Responses (MPB Path) 45 Hz ≤ f < 200 Hz from carrier frequency < 1 GHz -10 dBm -98 dBc, includes line-related f ≥ 200 Hz from carrier frequency < 1 GHz -10 dBm -94 dBc 45 Hz ≤ f < 200 Hz from carrier frequency ≥ 1 GHz -10 dBm -77 dBc +
20*log(carrier/GHz), includes line-related
f ≥ 200 Hz from carrier frequency ≥ 1 GHz -10 dBm -91 dBc +
20*log(N), includes line-related
标配通路 (扫描, Preselector 开, PA 关)
Frequency of the Fundamental Mixer Level Distortion SHI 10 to 15 MHz (Direct) -12 dBm -57 dBc +45 dBm 10 to 400 MHz -12 dBm -62 dBc
+50 dBm
> 400 to 600 MHz -12 dBm -56 dBc
+44 dBm
> 600 MHz to 1.2 GHz -12 dBm -59 dBc
+47 dBm
> 1.2 to 1.8 GHz -12 dBm -61 dBc
+49 dBm
> 1.8 to 2.3 GHz -12 dBm -77 dBc
+65 dBm
> 2.3 to 2.9 GHz -12 dBm -78 dBc
+66 dBm
> 2.9 to 3.2 GHz -12 dBm -76 dBc
+64 dBm
> 3.2 to 3.6 GHz -12 dBm -73 dBc
+61 dBm
> 3.6 to 4 GHz -12 dBm -76 dBc
+64 dBm
> 4 to 5.5 GHz -12 dBm -64 dBc
+52 dBm
> 5.5 to 11.5 GHz -12 dBm -75 dBc
+63 dBm
> 11.5 to 13 GHz -12 dBm -73 dBc
+61 dBm
> 13 to 16 GHz -12 dBm -72 dBc
+60 dBm
> 16 to 20 GHz -12 dBm -69 dBc
+57 dBm
> 20 to 23.5 GHz -12 dBm -67 dBc
+55 dBm
> 23.5 to 32.5 GHz -12 dBm -64 dBc
+52 dBm
> 32.5 to 33.5 GHz -12 dBm -61 dBc
+49 dBm
标配通路 (扫描, Preselector 开, PA 低)
条件：Frequency of the Fundamental Preamp Level Distortion, Nominal SHI, Nominal
10 to 15 MHz -27 dBm -44 dBc
+10 dBm
> 15 to 50 MHz -27 dBm -49 dBc
+21 dBm
> 50 MHz to 1.8 GHz -27 dBm -50 dBc
+22 dBm
> 1.8 to 8 GHz -27 dBm -51 dBc
+22 dBm
> 8 to 11 GHz -27 dBm -57 dBc
+27 dBm
>11 to 13 GHz -27 dBm -53 dBc
+24 dBm
>13 to 27 GHz -27 dBm -52 dBc
+23 dBm
>27 to 30 GHz -27 dBm -53 dBc
+26 dBm
>30 to 31 GHz -27 dBm -45 dBc
+18 dBm
>31 to 33.5 GHz -27 dBm -42 dBc
+14 dBm
标配通路 (扫描, Preselector 开, PA 高)
条件：Frequency of the Fundamental Mixer Level Distortion, Nominal SHI, Nominal
10 to 15 MHz -32 dBm -75 dBc
+10 dBm
> 15 to 50 MHz -32 dBm -83 dBc
+18 dBm
> 50 MHz to 1.8 GHz -32 dBm -82 dBc
+17 dBm
> 1.8 to 8 GHz -32 dBm -82 dBc
+17 dBm
> 8 to 11 GHz -32 dBm -89 dBc
+24 dBm
>11 to 14 GHz -32 dBm -85 dBc
+20 dBm
>14 to 22 GHz -32 dBm -81 dBc
+16 dBm
>22 to 28 GHz -32 dBm -77 dBc
+12 dBm
>28 to 29 GHz -32 dBm -75 dBc
+10 dBm
>29 to 31 GHz -32 dBm -70 dBc
+5 dBm
>31 to 33.5 GHz -32 dBm -65 dBc
0 dBm
标配通路 (扫描, Preselector 开, PA 关)
条件：Frequency Full Range 20 to 30 °C Typical, Unless Otherwise Stated
>34 to 39 GHz +23 dBm (nominal)
>39 to 40 GHz +21 dBm (nominal)
>40 to 45 GHz +19 dBm (nominal)
>45 to 56 GHz +21 dBm (nominal)
>56 to 60 GHz +24 dBm (nominal)
>60 to 64 GHz +27 dBm (nominal)
>64 to 67 GHz +29 dBm (nominal)
Two –12 dBm (up to 40 GHz), or –5 dBm (> 40 to 67 GHz) tones at input mixer with tone separation =
1 MHz
12 to 30 MHz +21 dBm +21 dBm
+26 dBm
> 30 to 800 MHz +11 dBm +12 dBm
+19 dBm
> 800 MHz to 1.3 GHz +9 dBm +9 dBm
+18 dBm
>1.3 to 3 GHz +16 dBm +17 dBm
+24 dBm
>3 to 4 GHz +16 dBm +17 dBm
+23 dBm
>4 to 8 GHz +16 dBm +16 dBm
+21 dBm
>8 to 10 GHz +10 dBm +10 dBm
+16 dBm
>10 to 13 GHz +14 dBm +15 dBm
+19 dBm
>13 to 16 GHz +15 dBm +15 dBm
+20 dBm
>16 to 19 GHz +15 dBm +16 dBm
+20 dBm
>19 to 20 GHz +16 dBm +16 dBm
+21 dBm
>20 to 26 GHz +17 dBm +17 dBm
+22 dBm
>26 to 30 GHz +18 dBm +18 dBm
+23 dBm
>30 to 34 GHz +18 dBm +19 dBm
+24 dBm
标配通路 (扫描, Preselector 开, PA 低)
条件：Frequency Nominal 10 to 30 MHz +8 dBm
Two –23 dBm (up to 40GHz); or –27 dBm (> 40 to 67 GHz) tones at preamp input with tone separation ≥
1 MHz
> 30 to 1.5 GHz
+8 dBm
> 1.5 to 8 GHz
+11 dBm
> 8 to 10 GHz
+8 dBm
> 10 to 15 GHz
+10 dBm
> 15 to 21 GHz
+11 dBm
> 21 to 26.5 GHz
+13 dBm
> 26.5 to 28 GHz
+14 dBm
> 28 to 34 GHz
+15 dBm
> 34 to 39.5 GHz
+6 dBm
> 39.5 to 45 GHz
+6 dBm
> 45 to 58 GHz
+10 dBm
> 58 to 60 GHz
+11 dBm
> 60 to 67 GHz
+12 dBm
标配通路 (扫描, Preselector 开, PA 高)
条件：Frequency Nominal 10 to 30 MHz +4 dBm
Two –33 dBm (up to 40 GHz); or –40 dBm (> 40 to 67 GHz) tones at preamp input with tone separation ≥
1 MHz
> 30 to 500 MHz
0 dBm
> 500 MHz to 1 GHz
+1 dBm
> 1 to 1.3 GHz
+3 dBm
> 1.3 to 4.5 GHz
+5 dBm
> 4.5 to 10 GHz
0 dBm
> 10 to 15 GHz
+2 dBm
> 15 to 20 GHz
-2 dBm
> 20 to 24 GHz
-1 dBm
> 24 to 26 GHz
0 dBm
> 26 to 34 GHz
+1 dBm
> 34 to 40 GHz
-2 dBm
> 40 to 44 GHz
-4 dBm
> 44 to 50 GHz
-1 dBm
DATA SHEET
> 50 to 55 GHz
-2 dBm
> 55 to 60 GHz
-1 dBm
> 60 to 67 GHz
+3 dBm
MPB 通路 (扫描, Preselector 关, PA 低)
Two –23 dBm (up to 40 GHz); or –27 dBm (> 40 to 67 GHz) tones at preamp input with tone separation ≥
1 MHz
频率标称值
> 8.5 to 10 GHz
+9 dBm
> 10 to 16 GHz
+12 dBm
> 16 to 18 GHz
+14 dBm
> 18 to 26 GHz
+15 dBm
> 26 to 34 GHz
+17 dBm
> 34 to 40 GHz
+11 dBm
> 40 to 42 GHz
+10 dBm
> 42 to 57 GHz
+11 dBm
> 57 to 61 GHz
+12 dBm
> 61 to 67 GHz
+13 dBm
MPB 通路 (扫描, Preselector 关, PA 高)
Two –33 dBm (up to 40GHz); or –40 dBm (> 40 GHz to 67 GHz) tones at preamp input with tone separation ≥
1 MHz
频率标称值
> 8.5 to 10 GHz
+1 dBm
> 10 to 15.5 GHz
+4 dBm
> 15.5 to 18.5 GHz
+2 dBm
> 18.5 to 25 GHz
+3 dBm
> 25 to 34.5 GHz
+4 dBm
> 34.5 to 59 GHz
0 dBm
> 59 to 67 GHz
+3 dBm
相位噪声 (SSB)
Phase Noise Offset Full Range
20 to 30 °C Typical, Unless
条件：Noise sidebands (CF = 1 GHz) 10 Hz –104 dBc/Hz (nominal) –104 dBc/Hz –104 dBc/Hz
100 Hz –114 dBc/Hz (nominal) –114 dBc/Hz –113 dBc/Hz
Noise sidebands (CF = 10 GHz) 10 Hz –82 dBc/Hz (nominal) –82 dBc/Hz –81 dBc/Hz
100 Hz –94 dBc/Hz (nominal) –94 dBc/Hz –93 dBc/Hz
Figure 10. Nominal PXA phase noise at various center frequencies. 50 GHz curve is the predicted
analyzer phase noise in resolving two closely spaced signals for various RBW filter choices.
1 kHz –126 dBc/Hz –126 dBc/Hz –129 dBc/Hz –130 dBc/Hz
–127 dBc/Hz
10 kHz –136 dBc/Hz –136 dBc/Hz –139 dBc/Hz –140 dBc/Hz
–135 dBc/Hz
100 kHz –141 dBc/Hz –141 dBc/Hz –144 dBc/Hz –146 dBc/Hz
–143 dBc/Hz
1 MHz –146 dBc/Hz –146 dBc/Hz –149 dBc/Hz –151 dBc/Hz
–150 dBc/Hz
10 MHz –153 dBc/Hz –154 dBc/Hz –156 dBc/Hz –153 dBc/Hz
–157 dBc/Hz
1 kHz –118 dBc/Hz –122 dBc/Hz
–121 dBc/Hz
10 kHz –132 dBc/Hz –134 dBc/Hz
–132 dBc/Hz
100 kHz –137 dBc/Hz –139 dBc/Hz
–138 dBc/Hz
1 MHz –146 dBc/Hz –147 dBc/Hz
–147 dBc/Hz
10 MHz –158 dBc/Hz –149 dBc/Hz
–159 dBc/Hz
phase noise computed from the
24 GHz observation. RBW curves added to show impact of
1Hz 10Hz 100Hz 1kHz 10kHz 100kHz 1MHz 10MHz
100MHz
RBW=1 kHz
RBW=10 kHz
RBW=100 kHz
RBW=100 Hz
IQ 分析仪
条件：specifications apply under the following settings unless otherwise specified: preselector
Each bandwidth option includes and enables all others with lesser bandwidth: e.g. instruments with
R80 also have R40 licenses, plus R20, B4X, and B40 paths.
40 MHz Analysis Bandwidth (Option B40)
Specifications on this bandwidth apply with center frequencies of 65 MHz and higher. All
bypassed, PA off, IF gain = Auto, IF gain offset =
0 dB.
Analysis bandwidth range
10 Hz to 40 MHz
Tuning range
2 Hz to 67 GHz
In practice, low end of tuning range limited to < (½*BW), by image folding and
LO feedthrough.
67.0 to 110 GHz with V3050A
Over-range tuning to 50.5 GHz allowed,
but without corrections, performance not specified
IF frequency 7.77 GHz (1st IF, center frequency ≤
8.2 GHz)
570 MHz (Final IF)
ADC sample rate
200 MSa/sec
ADC resolution
16 bits
Final data format I & Q pairs, 32 bits each
64 bits/Sa
IQ-pair sample rate
1.25 x BW
Capture memory
2 GB
IQ analyzer
128,000,001 sample pairs
Length (IQ sample pairs)
268,435,456 (228 Sa) with 64-bit data packing
Maximum capture time (time record length) 5.36 sec at full
40 MHz BW with 64-bit data packing
Capture time increases linearly with decrease in bandwidth
IF Frequency Response (Span ≤ 40 MHz, MPB Path
10 dB Attenuation)
条件：Full range 20 to 30 °C Nominal Nominal Nominal Nominal Nominal Nominal
65 MHz to 3.6 GHz ±0.6 ±0.5 ±0.07 0.03 ± 0.18 0.06 ±0.19
0.06
> 3.6 to 8.2 GHz ±0.7 ±0.6 ±0.13 0.04 ± 0.15 0.05 ±0.15
0.04
> 8.2 to 12 GHz ±0.7 ±0.6 ±0.09 0.02 ± 0.21 0.09 ±0.21
0.09
> 12 to 37.4 GHz ±1.1 ±1.0 ±0.13 0.04 ± 0.23 0.10 ±0.33
0.13
> 37.4 to 53.4 GHz ±1.3 ±1.2 ±0.16 0.04 ± 0.18 0.08 ±0.35
0.12
> 53.4 to 59 GHz ±1.4 ±1.2 ±0.13 0.04 ± 0.18 0.06 ±0.60
0.11
> 59 to 66 GHz ±1.7 ±1.5 ±0.13 0.04 ± 0.18 0.06 ±0.60
0.11
> 66 to 66.98 GHz ±2.4 ±2.3 ±0.13 0.04 ± 0.18 0.06 ±0.60
0.11
IF 相位线性度
条件：Center Frequency Span (MHz) Preselector RMS (Nominal)
IF Dynamic Range (IF Gain = High, Signal at –20 dBFS, Anywhere in Full IF Width) (Nominal)
IF Residual Responses (Input Terminated, 0 dB Attenuation, IF Gain = High) (Nominal)
≤ 8.2 GHz ≤ 40 MHz NA
0.08⁰
> 8.2 to 37.4 GHz ≤ 40 MHz Off
0.08⁰
> 37.4 to 53.4 GHz ≤ 40 MHz Off
0.1⁰
> 53.4 to 67 GHz ≤ 40 MHz Off
0.17⁰
SFDR (spurious-free dynamic range) (ADC related spurious)
-86 dBc
Center Frequency 65 MHz to 8.2 GHz
-115 dBm
> 8.2 GHz
-110 dBm
DATA SHEET
条件：Signal to Noise Ratio (Ratio of Clipping Level to Noise Level, Log Averaged, 1 Hz RBW, IF Gain = Low) (Nominal)
Center Frequency 65 MHz to 3.6 GHz
149 dB
> 3.6 to 26.5 GHz
146 dB
> 26.5 to 37.4 GHz
144 dB
> 37.4 to 53.4 GHz
142 dB
> 53.4 GHz
138 dB
TOI (3rd-Order Intermodulation Distortion in the IF, 2 Tones of Equal Level at -30 dBFS
1 MHz Tone Separation, IF Gain =
高) (标称值)
Center Frequency 65 MHz to 37.4 GHz
-83 dBc
> 37.4 to 67 GHz
-81 dBc
Noise Density in IF
条件：Nominally 2 dB higher than DANL MPB PA Off specification under similar measurement conditions.
Nominally 2 dB higher than DANL MPB PA High specification under similar measurement conditions.
The noise level in the IF will change for frequencies away from the center of the IF.
Spurious Responses (Preselector Enabled for Frequencies > 8.2 GHz) (Nominal)
Center Frequency Nominal 65 MHz to 8.2 GHz -110 dBm
Residual responses (input terminated
0 dB attenuation, IF gain = high)
> 8.2 GHz
-105 dBm
Tuned Frequency (f) Excitation Frequency
≤ 8.2 GHz f + 2 *
1st IF MHz
f +
2 * Final IF MHz
> 8.2 GHz f +
2 * Final IF MHz
Amplitude Accuracy, Absolute (MPB Path
10 dB Attenuation)
PA 关 PA 低 PA 高
条件：Center Frequency Full Range 20 to 30 °C Nominal Nominal
specifications apply under the following settings unless otherwise specified: preselector
30 to 50 MHz ±0.86 dB ±0.76 dB ±0.17 dB
±0.18 dB
> 50 to 125 MHz ±0.8 dB ±0.66 dB ±0.17 dB
±0.18 dB
> 125 MHz to 3.6 GHz ±0.84 dB ±0.66 dB ±0.17 dB
±0.18 dB
> 3.6 to 5.3 GHz ±0.78 dB ±0.71 dB ±0.21 dB
±0.22 dB
> 5.3 to 8.2 GHz ±0.85 dB ±0.75 dB ±0.16 dB
±0.19 dB
> 8.2 to 12 GHz ±1.34 dB ±1.15 dB ±0.27 dB
±0.25 dB
> 12 to 15.4 GHz ±2.3 dB ±1.79 dB ±0.17 dB
±0.18 dB
> 15.4 to 37.4 GHz ±2.3 dB ±1.79 dB ±0.37 dB
±0.38 dB
> 37.4 to 53.4 GHz ±2.27 dB ±1.94 dB ±0.41 dB
±0.53 dB
> 53.4 to 55 GHz ±2.2 dB ±1.95 dB ±0.4 dB
±0.49 dB
> 55 to 59 GHz ±2.78 dB ±2.33 dB ±0.52 dB
±0.70 dB
> 59 to 66 GHz ±3.11 dB ±2.66 dB ±0.6 dB
±0.77 dB
> 66 to 67 GHz ±3.61 dB ±3.16 dB ±0.6 dB
±0.77 dB
DATA SHEET
480 MHz Analysis Bandwidth (Option B4X)
Specifications on this bandwidth apply with center frequencies of 300 MHz and higher. All
bypassed, PA off, IF gain = Auto, IF gain offset =
0 dB.
Analysis bandwidth range
10 Hz to 480 MHz
Tuning range
2 Hz to 67 GHz
In practice, low end of tuning range limited to < (½*BW), by image folding and
LO feedthrough.
67.0 to 110 GHz with V3050A
Over-range tuning to 50.5 GHz allowed,
but without corrections, performance not specified
IF frequency 8.1 GHz (1st IF, center frequency ≤
8.2 GHz)
900 MHz (Final IF)
ADC sample rate
1000 MSa/sec
ADC resolution
16 bits
Final data format I & Q pairs, 32 bits each
64 bits/Sa
IQ-pair sample rate
1.25 x BW
Capture memory
2 GB
IQ analyzer
128,000,001 sample pairs
Length (IQ sample pairs)
268,4 MSa (228 Sa) with 64-bit data packing
Maximum capture time (time record length) 0.447 second at full
480 MHz BW with 64-bit data packing
Capture time increases linearly with decrease in bandwidth
IF Frequency Response (Span ≤ 480 MHz, MPB Path
10 dB Attenuation)
条件：Full range 20 to 30 °C Nominal Nominal Nominal Nominal Nominal Nominal
300 MHz to 3.5 GHz ±1.3 ±1.1 ±0.4 0.13 ±0.23 0.06 ±0.21
0.06
> 3.5 to 8.2 GHz ±1.1 ±0.8 ±0.17 0.05 ±0.30 0.09 ±0.28
0.09
> 8.2 to 12 GHz ±1.1 ±0.8 ±0.12 0.04 ±0.31 0.08 ±0.30
0.08
> 12 to 37.1 GHz ±1.8 ±1.4 ±0.27 0.08 ±0.71 0.27 ±0.47
0.20
> 37.1 to 53.1 GHz ±2.0 ±1.7 ±0.30 0.10 ±0.41 0.15 ±0.52
0.20
> 53.1 to 59 GHz ±2.7 ±2.2 ±0.31 0.12 ±0.64 0.24 ±0.70
0.25
> 59 to 66 GHz ±3.0 ±2.5 ±0.31 0.12 ±0.64 0.24 ±0.70
0.25
> 66 to 66.76 GHz ±3.7 ±3.3 ±0.31 0.12 ±0.64 0.24 ±0.70
0.25
IF 相位线性度
条件：Center Frequency Span (MHz) Preselector RMS (Nominal)
IF Dynamic Range (IF Gain = High, Signal at –20 dBFS, Anywhere in Full IF Width) (Nominal)
≤ 8.2 GHz ≤ 480 MHz NA
0.3⁰
> 8.2 to 37.1 GHz ≤ 480 MHz Off
0.3⁰
> 37.1 to 53.1 GHz ≤ 480 MHz Off
0.6⁰
> 53.1 to 67 GHz ≤ 480 MHz Off
0.75⁰
SFDR (杂散-free 动态范围) (ADC related 杂散)
条件：IF Residual Responses (Input Terminated, 0 dB attenuation, IF gain = high) (Nominal)
-70 dBc
Center Frequency 300 MHz to 3.5 GHz
-99 dBm
> 3.5 to 8.2 GHz
-98 dBm
> 8.2 to 12.1 GHz
-96 dBm
> 12.1 to 37.1 GHz
-83 dBm
> 37.1 to 53.1 GHz
-91 dBm
> 53.1 GHz
-86 dBm
DATA SHEET
条件：Signal to Noise Ratio (Ratio of Clipping Level to Noise Level, Log Averaged, 1 Hz RBW, IF Gain = Low) (Nominal)
Center Frequency 300 MHz to 3.5 GHz
155 dB
> 3.5 to 8.2 GHz
150 dB
> 8.2 to 12 GHz
152 dB
> 12 to 37.1 GHz
151 dB
> 37.1 to 53.1 GHz
148 dB
> 53.1 GHz
145 dB
TOI (3rd-Order Intermodulation Distortion in the IF, 2 Tones of Equal Level at -25 dBFS
10 MHz Tone Separation, IF Gain =
高) (标称值)
Center Frequency 300 MHz 3.5 GHz
-92 dBc
> 3.5 to 8.2 GHz
-91 dBc
> 8.2 to 37.1 GHz
-95 dBc
> 37.1 to 53.1 GHz
-91 dBc
> 53.1 GHz
-92 dBc
Noise Density in IF
条件：Nominally 2 dB higher than DANL MPB PA Off specification under similar measurement conditions.
Nominally 2 dB higher than DANL MPB PA High specification under similar measurement conditions.
The noise level in the IF will change for frequencies away from the center of the IF.
Spurious Responses (Preselector Enabled for Frequencies > 8.2 GHz) (Nominal)
Center Frequency Nominal 300 MHz to 1.7 GHz -100 dBm
Residual responses (input terminated
0 dB attenuation, IF gain = high)
> 1.7 to 1.9 GHz
-95 dBm
> 1.9 GHz
-100 dBm
Tuned Frequency (f) Excitation Frequency
≤ 8.2 GHz f + 2 *
1st IF MHz
f +
2 * Final IF MHz
> 8.2 GHz f +
2 * Final IF MHz
Amplitude Accuracy, Absolute (MPB path
10 dB Attenuation)
PA 关 PA 低 PA 高
条件：Center Frequency Full Range 20 to 30 °C Nominal Nominal
specifications apply under the following settings unless otherwise specified: preselector
260 MHz to 3.5 GHz ±0.81 dB ±0.67 dB ±0.14 dB
±0.14 dB
> 3.5 to 8.2 GHz ±1.06 dB ±0.87 dB ±0.2 dB
±0.22 dB
> 8.2 to 12 GHz ±1.25 dB ±1.13 dB ±0.25 dB
±0.25 dB
> 12 to 15.2 GHz ±1.67 dB ±1.44 dB ±0.19 dB
±0.2 dB
> 15.2 to 24 GHz ±1.67 dB ±1.44 dB ±0.4 dB
±0.41 dB
> 24 to 37.1 GHz ±2.19 dB ±1.53 dB ±0.4 dB
±0.41 dB
> 37.1 to 53.1 GHz ±2.26 dB ±1.94 dB ±0.37 dB
±0.45 dB
> 53.1 to 55 GHz ±2.03 dB ±1.8 dB ±0.55 dB
±0.62 dB
> 55 to 59 GHz ±2.73 dB ±2.33 dB ±0.55 dB
±0.62 dB
> 59 to 66 GHz ±2.86 dB ±2.42 dB ±0.55 dB
±0.62 dB
> 66 to 67 GHz ±3.41 dB ±2.97 dB ±0.55 dB
±0.62 dB
DATA SHEET
2 GHz Analysis Bandwidth (Option R20)
Specifications on this bandwidth apply with center frequencies of 1200 MHz and higher. All
bypassed, PA off, IF gain = Auto, IF gain offset =
0 dB.
Analysis bandwidth range
10 Hz to 2 GHz
Tuning range 2 Hz to 67 GHz In practice, low end of tuning range limited to < (½*BW), by image folding and LO feedthrough.
67.0 to 110 GHz with V3050A Over-range tuning to 50.5 GHz allowed, but
without corrections, performance not specified
IF frequency 8.4 GHz (1st IF, center frequency ≤
8.2 GHz)
1.2 GHz (Final IF)
ADC sample rate
2400 MSa/sec
ADC resolution
14 bits
Final data format I & Q pairs, 32 bits each
64 bits/Sa
IQ-pair sample rate
1.25 x BW
Capture memory
16 GB
IQ analyzer
32,000,001 sample pairs
Length (IQ sample pairs)
268,4 MSa (228 Sa) with 64-bit data packing
Maximum capture time (time record length) 3.57 second at full
2 GHz BW with 64-bit data packing
Capture time increases linearly with decrease in bandwidth
IF Frequency Response (Span ≤ 2 GHz, MPB Path
10 dB Attenuation)
条件：Full range 20 to 30 °C Nominal Nominal Nominal Nominal Nominal Nominal
1.2 to 3.5 GHz ±1.5 ±1.2 ±0.31 0.10 ±0.52 0.15 ±0.51
0.14
> 3.5 to 8.2 GHz ±1.0 ±0.9 ±0.21 0.05 ±0.40 0.11 ±0.41
0.11
> 8.2 to 12 GHz ±1.3 ±1.1 ±0.30 0.07 ±0.30 0.13 ±0.32
0.13
> 12 to 36.8 GHz ±2.0 ±1.7 ±0.30 0.08 ±0.87 0.26 ±0.62
0.18
> 36.8 to 52.8 GHz ±1.9 ±1.6 ±0.28 0.10 ±0.49 0.16 ±0.56
0.21
> 52.8 to 55 GHz ±2.9 ±2.5 ±0.39 0.14 ±0.63 0.27 ±0.93
0.27
> 55 to 66 GHz ±3.1 ±2.7 ±0.39 0.14 ±0.63 0.27 ±0.93
0.27
IF 相位线性度
条件：Center Frequency Span (MHz) Preselector RMS (Nominal)
IF Dynamic Range (IF Gain = High, Signal at –16 dBFS, Anywhere in Full IF Width) (Nominal)
≤ 8.2 GHz ≤ 2000 MHz NA
0.5⁰
> 8.2 to 67 GHz ≤ 2000 MHz Off
0.5⁰
SFDR (杂散-free 动态范围) (ADC related 杂散)
条件：IF Residual Responses (Input Terminated, 0 dB Attenuation, IF Gain = High) (Nominal)
Signal to Noise Ratio (Ratio of Clipping Level to Noise Level, Log Averaged, 1 Hz RBW, IF Gain = Low) (Nominal)
-61 dBc
Center Frequency 1.2 to 8.2 GHz
-90 dBm
> 8.2 GHz
-95 dBm
Center Frequency 1.2 to 3.5 GHz
152 dB
> 3.5 to 8.2 GHz
150 dB
> 8.2 to 12 GHz
149 dB
> 12 to 36.8 GHz
145 dB
> 36.8 to 52.8 GHz
142 dB
> 52.8 GHz
138 dB
DATA SHEET
TOI (3rd-Order Intermodulation Distortion in the IF, 2 Tones of Equal Level at -20 dBFS
10 MHz Tone Separation, IF Gain =
高) (标称值)
Center Frequency 1.2 to 12 GHz
-82 dBc
> 12 GHz
-83 dBc
Noise Density in IF
条件：Nominally 2 dB higher than DANL MPB PA Off specification under similar measurement conditions.
Nominally 2 dB higher than DANL MPB PA High specification under similar measurement conditions.
The noise level in the IF will change for frequencies away from the center of the IF.
Spurious Responses (Preselector Enabled for Frequencies > 8.2 GHz) (Nominal)
Center Frequency Nominal 1.2 to 8.2 GHz -95 dBm
Residual responses (input terminated
0 dB attenuation, IF gain = high)
> 8.2 GHz
-100 dBm
Tuned Frequency (f) Excitation Frequency
≤ 8.2 GHz f + 2 *
1st IF MHz
f +
2 * Final IF MHz
> 8.2 GHz f +
2 * Final IF MHz
Amplitude Accuracy, Absolute (MPB Path
10 dB Attenuation)
PA 关 PA 低 PA 高
条件：Center Frequency Full Range 20 to 30 °C Nominal Nominal
specifications apply under the following settings unless otherwise specified: preselector
1.02 to 1.8 GHz ±0.69 dB ±0.57 dB ±0.29 dB
±0.26 dB
> 1.8 to 3.5 GHz ±0.69 dB ±0.57 dB ±0.17 dB
±0.16 dB
> 3.5 to 8.2 GHz ±0.94 dB ±0.76 dB ±0.2 dB
±0.19 dB
> 8.2 to 12 GHz ±1.2 dB ±1.07 dB ±0.25 dB
±0.27 dB
> 12 to 14.8 GHz ±1.58 dB ±1.37 dB ±0.2 dB
±0.2 dB
> 14.8 to 25 GHz ±1.58 dB ±1.37 dB ±0.35 dB
±0.44 dB
> 25 to 36.8 GHz ±2.16 dB ±1.5 dB ±0.35 dB
±0.44 dB
> 36.8 to 52.8 GHz ±2.34 dB ±2 dB ±0.44 dB
±0.6 dB
> 52.8 to 55 GHz ±2.28 dB ±2.02 dB ±0.43 dB
±0.5 dB
> 55 to 59 GHz ±2.68 dB ±2.35 dB ±0.55 dB
±0.75 dB
> 59 to 66 GHz ±3.16 dB ±2.72 dB ±0.65 dB
±0.8 dB
> 66 to 67 GHz ±3.59 dB ±3.15 dB ±0.65 dB
±0.8 dB
DATA SHEET
4 GHz Analysis Bandwidth (Option R40)
Specifications on this bandwidth apply with center frequencies of 2500 MHz and higher. All
bypassed, PA off, IF gain = Auto, IF gain offset =
0 dB.
Analysis bandwidth range
8 kHz to 4 GHz
Tuning range
2 to 67 GHz
In practice, low end of tuning range limited to < (½*BW), by image folding and
LO feedthrough.
67.0 to 110 GHz with V3050A
Over-range tuning to 50.5 GHz allowed,
but without corrections, performance not specified
IF frequency 15.8 GHz (1st IF, center frequency ≤ 8.0 GHz) 3 GHz (Final IF, center frequency ≤ 10.0 GHz) 5 GHz (Final IF, center frequency >
10.0 GHz)
ADC sample rate
20 GSa/sec
ADC resolution
14 bits
Final data format I & Q pairs
64 bits/Sa
IQ-pair sample rate
1.25 x BW
Capture memory
16 GB
IQ analyzer
32,000,001 sample pairs
Length (IQ sample pairs)
4 GSa with 32-bit data packing
Maximum capture time (time record length)
0.858 second at full BW with 32-bit data packing
IF Frequency Response (Span ≤ 4 GHz, MPB Path
10 dB Attenuation)
条件：Full range 20 to 30 °C Nominal Nominal Nominal Nominal Nominal Nominal
2.5 to 8 GHz ±1.10 ±0.90 ±0.18 0.11 ±0.28 0.06 ±0.28
0.07
> 8 to 14 GHz ±1.30 ±1.00 ±0.23 0.10 ±0.26 0.07 ±0.23
0.07
> 14 to 35 GHz ±1.40 ±1.10 ±0.25 0.11 ±0.40 0.13 ±0.42
0.15
> 35 to 49 GHz ±1.70 ±1.40 ±0.26 0.12 ±0.37 0.14 ±0.62
0.20
> 49 to 59 GHz ±3.10 ±2.60 ±0.45 0.14 ±0.59 0.22 ±1.00
0.32
> 59 to 65 GHz ±3.60 ±3.00 ±0.45 0.14 ±0.59 0.22 ±1.00
0.32
IF 相位线性度
条件：Center Frequency Span (MHz) Preselector RMS (Nominal)
IF Dynamic Range (IF Gain = High, Signal at –24 dBFS, Anywhere in Full IF Width) (Nominal)
≤ 8 GHz ≤ 4000 MHz N/A
0.8⁰
> 8 to 14 GHz ≤ 4000 MHz Off
1.2⁰
> 14 to 35 GHz ≤ 4000 MHz Off
1⁰
> 35 to 49 GHz ≤ 4000 MHz Off
2.6⁰
> 49 to 65 GHz ≤ 4000 MHz Off
2.4⁰
SFDR (杂散-free 动态范围) (ADC related 杂散)
条件：IF Residual Responses (Input Terminated, 0 dB Attenuation, IF Gain = High) (Nominal)
-53 dBc
Center Frequency 2.5 to 8 GHz -78 dBm 8 to 14 GHz
-85 dBm
> 14 GHz
-78 dBm
DATA SHEET
条件：Signal to Noise Ratio (Ratio of Clipping Level to Noise Level, Log Averaged, 1 Hz RBW, IF Gain = High) (Nominal)
Center Frequency 2.5 to 8 GHz
138 dB
> 8 to 35 GHz
144 dB
> 35 to 49 GHz
139 dB
> 49 to 65 GHz
138 dB
TOI (3rd-Order Intermodulation Distortion in the IF, 2 Tones of Equal Level at -14 dBFS
10 MHz Tone Separation, IF Gain =
高) (标称值)
Center Frequency 2.5 to 35 GHz
-68 dBc
> 35 GHz
-69 dBc
Noise Density in IF
条件：Nominally 2 dB higher than DANL MPB PA Off specification under similar measurement conditions.
For frequencies < 60 GHz nominally
2 dB higher than DANL MPB PA High specification under similar measurement
For frequencies ≥ 60 GHz nominally
6 dB higher than DANL MPB PA High specification under similar measurement
条件：The noise level in the IF will change for frequencies away from the center of the IF.
Spurious Responses (Preselector Enabled for Frequencies > 8.0 GHz) (Nominal)
Center Frequency Nominal 2.5 to 8.0 GHz -80 dBm
Residual responses (input terminated
0 dB attenuation, IF gain = high)
> 8.0 GHz
-100 dBm
Tuned Frequency (f) Excitation Frequency
≤ 8.0 GHz f + 2 *
1st IF MHz
f +
2 * Final IF MHz
> 8.0 GHz f +
2 * Final IF MHz
Amplitude Accuracy, Absolute (MPB path
10 dB Attenuation)
PA 关 PA 低 PA 高
条件：Center frequency Full range 20 to 30 °C Nominal Nominal
specifications apply under the following settings unless otherwise specified: preselector
2.15 to 8.2 GHz ±1.18 dB ±1.02 dB ±0.3 dB
±0.33 dB
> 8.2 to 14 GHz ±1.85 dB ±1.45 dB ±0.26 dB
±0.28 dB
> 14 to 25 GHz ±1.93 dB ±1.63 dB ±0.31 dB
±0.33 dB
> 25 to 35 GHz ±2.39 dB ±1.7 dB ±0.38 dB
±0.45 dB
> 35 to 49 GHz ±2.44 dB ±2.06 dB ±0.4 dB
±0.43 dB
> 49 to 55 GHz ±2.41 dB ±2.08 dB ±0.55 dB
±0.7 dB
> 55 to 59 GHz ±2.9 dB ±2.52 dB ±0.6 dB
±1.0 dB
> 59 to 66 GHz ±3.22 dB ±2.74 dB ±0.73 dB
±1.3 dB
> 66 to 67 GHz ±3.7 dB ±3.22 dB ±0.73 dB
±1.3 dB
DATA SHEET
8 GHz Analysis Bandwidth (Option R80)
Specifications on this bandwidth apply with center frequencies of 9 GHz and higher. All
bypassed, PA off, IF gain = Auto, IF gain offset =
0 dB.
Analysis bandwidth range
8 kHz to 8 GHz
Tuning range 9 to 67 GHz In practice, low end of tuning range limited to < (½*BW), by image folding and LO feedthrough.
67.0 to 110 GHz with V3050A Over-range tuning to 50.5 GHz allowed, but
without corrections, performance not specified
5 GHz (Final IF)
ADC sample rate
20 GSa/sec
ADC resolution
14 bits
Final data format I & Q pairs
64 bits/Sa
IQ-pair sample rate
1.25 x BW
Capture memory
32 GB
IQ analyzer
32,000,001 sample pairs
Length (IQ sample pairs)
8 GSa with 32-bit data packing
Maximum capture time (time record length)
0.429 second at full BW with 32-bit data packing
IF Frequency Response (Span ≤ 8 GHz, MPB Path
10 dB Attenuation)
条件：Full range 20 to 30 °C Nominal Nominal Nominal Nominal Nominal Nominal 9 to 14 GHz ±1.9 ±1.5 ±0.34 0.10 ±0.35 0.10 ± 0.4 0.09
> 14 to 35 GHz ±2.7 ±2.0 ±0.36 0.10 ±0.70 0.25 ± 0.6
0.18
> 35 to 49 GHz ±2.8 ±2.2 ±0.34 0.10 ±0.50 0.25 ± 0.7
0.24
> 49 to 55 GHz ±3.9 ±3.0 ±0.43 0.15 ±1.00 0.25 ± 1.0
0.34
> 55 to 63 GHz ±4.3 ±3.4 ±0.40 0.15 ±1.00 0.25 ± 1.0
0.34
IF 相位线性度
条件：Center Frequency Span (MHz) Preselector RMS (Nominal)
IF Dynamic Range (IF Gain = High, Signal at –24 dBFS, Anywhere in Full IF Width) (Nominal)
IF Residual Responses (Input Terminated, 0 dB Attenuation, IF Gain = High) (Nominal)
Signal to Noise Ratio (Ratio of Clipping Level to Noise Level, Log Averaged, 1 Hz RBW, IF Gain = High) (Nominal)
≤ 14 GHz ≤ 8000 MHz Off
1.6⁰
> 14 to 35 GHz ≤ 8000 MHz Off
1.25⁰
> 35 to 49 GHz ≤ 8000 MHz Off
2.75⁰
> 49 to 63 GHz ≤ 8000 MHz Off
3.75⁰
SFDR (spurious-free dynamic range) (ADC related spurious)
-55 dBc
Center Frequency 9 to 11.4 GHz
-70 dBm
> 11.4 to 11.6 GHz
-53 dBm
> 11.6 to 12.9 GHz
-74 dBm
> 12.9 to 13.1 GHz
-63 dBm
> 13.1 to 29 GHz
-80 dBm
> 29 GHz
-90 dBm
Center Frequency 9 to 14 GHz
143 dB
> 14 to 35 GHz
144 dB
> 35 to 49 GHz
139 dB
> 49 GHz
137 dB
DATA SHEET
TOI (3rd-Order Intermodulation Distortion in the IF, 2 Tones of Equal Level at -14 dBFS
10 MHz Tone Separation, IF Gain =
高) (标称值)
Center Frequency 9 to 63 GHz
-68 dBc
Noise Density in IF
条件：Nominally 4 dB higher than DANL MPB PA Off specification under similar measurement conditions.
Nominally 1 dB higher than DANL MPB PA High specification under similar measurement conditions.
The noise level in the IF will change for frequencies away from the center of the IF.
Spurious Responses (Preselector Enabled for Frequencies > 8.0 GHz) (Nominal)
Center Frequency Nominal 9 to 11.4 GHz -70 dBm
Residual responses (input terminated
0 dB attenuation, IF gain = high)
> 11.4 to 11.6 GHz
-53 dBm
> 11.6 to 12.9 GHz
-74 dBm
> 12.9 to 13.1 GHz
-63 dBm
> 13.1 to 29 GHz
-80 dBm
> 29 GHz
-90 dBm
Tuned Frequency (f) Excitation Frequency
> 9.0 GHz f +
2 * Final IF MHz
Amplitude Accuracy, Absolute (MPB path
10 dB Attenuation)
PA 关 PA 低 PA 高
条件：Center frequency Full range 20 to 30 °C Nominal Nominal
9 to 14 GHz ±2.15 dB ±1.65 dB ±0.38 dB
±0.4 dB
> 14 to 25 GHz ±1.93 dB ±1.6 dB ±0.33 dB
±0.37 dB
> 25 to 35 GHz ±2.27 dB ±1.58 dB ±0.5 dB
±0.5 dB
> 35 to 49 GHz ±2.46 dB ±2.08 dB ±0.38 dB
±0.48 dB
> 49 to 55 GHz ±2.55 dB ±2.22 dB ±0.48 dB
±0.49 dB
> 55 to 59 GHz ±2.95 dB ±2.55 dB ±0.56 dB
±0.75 dB
> 59 to 66 GHz ±3.22 dB ±2.69 dB ±0.7 dB
±0.78 dB
> 66 to 67 GHz ±3.67 dB ±3.14 dB ±0.7 dB
±0.78 dB
四、通用规格
温度范围
Operating
0 to 40 °C
Storage
-40 to +70 °C
Altitude Operating: Up to 2,286 meters (7,500 feet)
Maximum relative humidity
95 %, non-condensing
供电要求
条件：Voltage and frequency (nominal) 100-120 V, 50/60/400 Hz The instruments can operate with mains supply voltage fluctuations up to ± 10
% of the nominal voltage 200-240 V, 50/60 Hz
Rated input power
1,400 W(maximum)
Power consumption, on
750 W (typical)
Power consumption, standby
7 W max
条件：Size 290 mm (11.6 in.) diagonal (nominal) capacitive multi-touch screen
Resolution 1920 x
1080
数据存储
Internal
1 TB removable solid-state drive
External Supports USB
3.0/2.0 compatible memory devices
CPU Intel Core i9 13900E, 24-core, 5.2 GHz max clock
128 GB DDR5 DRAM
GPU PCIe Gen 4 x16
16 GB GDDR6 SDRAM
Operating system Windows
-11, Enterprise
Height
187 mm (7.4 in)
Width
580 mm (22.8 in)
Length
775 mm (30.5 in)
RF Input
条件：Option 555/567 1.85 mm male 50 Ω (nominal) (standard)
Adapters 2.4 mm (f) to 2.4 mm (f)
2.92 mm (f) to 2.4 mm (f), and 2.4 mm (f) to 3.5 mm (f) included
类型说明连接器输出电流
条件：(1) 3.0 A at 15 V (right side)
USB 3 (4) Compatible with USB 3.2 Gen 2 USB Type-A female (blue)
0.9A at 5V
USB C PD (3) Compatible with USB Type-C
3.2
Gen
2
USB Type-C female (2)
3.0 A at 5 V
External Frequency Extender, Wide Bandwidth (Option EXW), Interface for Use with V3050A
LO Out
Connector
1.85 mm female; connection to V3050A signal analyzer frequency extender
IF In
条件：Connector SMA, female, 50 Ω nominal
Connector SMA, female, 50 Ω nominal
Output amplitude +10 dBm (nominal)
Connector BNC female,10 kΩ (nominal)
Connector BNC female, 50 Ω (nominal)
Level 1.5 to 5 V (CMOS) (nominal)
Bandwidth Supports all optional IFs up to and including
8 GHz
Maximum safe level
+7 dBm
Flatness Nominally dominated by mixer flatness after any amp corrections applied with some offset due to IF
cable losses
100 MHz Out
Frequency range
100 MHz
Trigger
1 Input
Trigger level range
–5 to 5 V
Trigger
1 Output
Ref Out
条件：Connector BNC female, 50 Ω (nominal)
Output amplitude +10 dBm (nominal)
Frequency
10 MHz × (1+ frequency reference accuracy)
Other frequency x (1+ frequency reference accuracy)
Ref In
条件：Connector BNC female, 50 Ω (nominal)
Input amplitude range -5 to +10 dBm (nominal)
Input frequency 2 to 110 MHz (nominal)
Frequency lock range ± 1 x
10-6 of specified external reference input frequency
2.4 GHz Out
连接器 SMA female
条件：Output amplitude +15 dBm (nominal)
Impedance
50 Ω (nominal)
Frequency
2.4 GHz (nominal)
2.4 GHz In
连接器 SMA female
条件：Input amplitude range +11 to +17 dBm (nominal)
Connector BNC female,10 kΩ (nominal)
Impedance
50 Ω (nominal)
Frequency
2.4 GHz (nominal)
Trigger
2 and 3 Inputs
Trigger level range
–5 to 5 V
Precision 触发 · (· Wide-带宽测量仅)
条件：Connector SMA, female, 50 Ω (nominal)
Connector BNC female, 50 Ω (nominal)
Trigger level range 1.5 to 5 V (CMOS) (nominal)
Trigger level range
–5 to 5 V
Trigger
2 and 3 Outputs
Noise Source Drive
+28 V (Pulsed)
连接器 BNC female
条件：Output voltage on 28.0 ±0.1 V (nominal, 60 mA maximum)
Output voltage off <
1.0 V
SNS Series Noise Source (For Use with Keysight Technologies’ SNS Series Noise Sources)
Connector
12-pin circular
连接器 SMA female
Impedance
50 Ω nominal
IF Out, Second IF Output, Licensed as Option CR3 (Included as Standard)
SA mode 522.5 MHz center frequency (RBW ≤
3 MHz)
570 MHz center frequency (stepped FFTs)
900 MHz center frequency (RBW >
3 MHz)
IQ analyzer in B40
570 MHz center frequency
IQ analyzer in B4X
900 MHz center frequency
USB Ports
USB
3.0 (4 Ports)
Standard Compatible with USB 3.2 Gen
2
连接器 USB 类型- female (blue)
Output current
0.9 A at 5 V
USB Type-C (1 port)
Standard Compatible with USB Type-C 3.2 Gen
2
连接器 USB 类型-C female
Output current
1.0 A at 5 V
Connector DisplayPort
Resolution 1920 x
1080
Micro GPIB Interface
Connector Mini IEEE-488 bus connector
GPIB codes SH1, AH1, T6, SR1, RL1, PP0, DC1, C1, C2, C3, C28, DT1, L4, C0
LAN TCP/IP Interface
Option GBE (10 Gbit Ethernet,
included as standard)
10G Base-T
Connector RJ45 Ethertwist
Thunderbolt (TB)
Standard Compatible with Thunderbolt
4
Connector USB Type C, female (2 ports)
Output current
3.0 A at 5 V
法规信息
This product is designed for use in INSTALLATION CATEGORY II and POLLUTION DEGREE
2 and
MEASUREMENT CATEGORY NONE
条件：has been supplied in a safe condition. The instruction documentation contains information and
This product has been designed and tested in accordance with accepted industry standards and
warnings which must be followed by the user to ensure safe operation and to maintain the product
Safety and Regulatory Markings which May be on the Product
The CE mark is a registered trademark of the European Community (if accompanied by a
year, it is the year when the design was proven). This product complies with all relevant
CAN ICES/NMB-001(A) Canada EMC label. Interference-Causing Equipment Standard for industrial, scientific
and medical (ISM) equipment. Matériel industriel, scientifique et médical (ISM)
ISM 1-A (GRP.1 CLASS A) This is a symbol of an Industrial Scientific and Medical Group
1 Class A product. (CISPR
11, Clause
4)
The CSA mark is a registered trademark of the CSA International.
The RCM mark is a registered trademark of the Australian Communications and Media
UK conformity mark is a UK government owned mark
Products showing this mark comply with all applicable UK regulations.
This symbol indicates separate collection for electrical and electronic equipment
mandated under EU law as of August 13
2005. All electric and electronic equipment are
required to be separated from normal waste for disposal (Reference WEEE Directive
2002/96/EC).
The crossed out wheeled bin symbol indicates that separate collection for waste electric
以上指标摘自厂家官方数据手册，完整定义、测试条件与保证值口径以手册为准。完整指标、测试条件与定义口径请见产品页「软件和手册 | 白皮书」栏目中的官方数据手册。
是德科技 | KEYSIGHT · onetest 仪器资源库
全部
是德科技官方渠道
官方渠道（官网 / 热线 / 邮箱）
• 销售服务热线
800-810-0189（座机）／400-810-0189（手机） 工作时间 周一至周五 8:30-17:30
• 热线传真
800-820-2816（座机）／400-820-3863（手机）
• 亚洲区支持邮箱 tm_asia@keysight.com
• 服务与支持邮箱
instruments_services@keysight.com
• 官网
www.keysight.com（中国站 www.keysight.com.cn）
全国办事处
• 北京总部
是德科技（中国）有限公司 北京市朝阳区望京北路3号
电话：(010) 64397888
传真：(010) 64390278
邮编：100102
• 上海分公司
上海市虹口区四川北路1350号中信泰富申虹广场5楼、16-19楼
电话：(021) 36127688
传真：(021) 36127188
邮编：200080
• 广州分公司
广州市天河北路233号中信广场66层07-08室
电话：(020) 38113988
传真：(020) 86695074
邮编：510613
• 深圳分公司
深圳市福田中心区福华一路六号免税商务大厦3楼
电话：(0755) 83079588
传真：(0755) 82763181
邮编：518048
• 成都分公司
成都高新区南部园区天府四街116号
电话：(028) 83108888
传真：(028) 85330830
邮编：610041
• 西安分公司
西安市碑林区南关正街88号长安国际大厦D座5/F
电话：(029) 88867770
传真：(029) 88861330
邮编：710068
• 中国香港
是德科技香港有限公司 中国香港北角电气道169号25楼
电话：(852) 31977777
传真：(852) 25069292 香港热线 800-938-693
• 维修 / 校准服务中心
中国大陆 北京 / 成都 / 苏州 服务热线 800-810-0189 / 400-810-0189
授权分销商
• 上海信果电子科技有限公司（上海）
上海市沪闵路8075号虹梅商务大厦6楼609室
邮编：200233
电话：021-64518399
传真：021-54560890
邮箱：jason.wu@signalgroup.com.tw
• 上海精测电子有限公司（上海）
上海市北京东路668号西楼15E
邮编：200001
电话：13916371522
传真：021-53086102
邮箱：yangzhen@jingce.com
• 北京东方中科集成科技股份有限公司（北京）
北京市海淀区复兴路69号院12号楼2层、7层 邮政编码：100039
邮编：100039
电话：400-650-5566
传真：010-68728001
邮箱：zhangzp@oimec.com.cn
官网：www.dfzk.com/br_keysight.html
• 北京千聚科技发展有限公司（北京）
北京市海淀区西三旗花园雪梨澳乡A区23-4号
邮编：100085
电话：010-82907162
邮箱：zhuqihui@qianjukeji.com.cn
• 北京金龙翌阳科技发展有限公司（北京）
北京市海淀区大柳树路17号富海大厦2001室
邮编：100086
电话：010-62167379/6213538
邮箱：zhy@yy17.com
官网：www.yy17.com
• 厦门同昌源电子有限公司（厦门）
厦门市湖里区悦华路215号综合楼二楼C单元
邮编：361000
电话：0592-5663715
传真：0592-2236795
邮箱：tcydz@xmtcy.com
• 合肥新普仪测科技有限公司（合肥）
安徽省合肥市长江路53号长江大厦1102室
邮编：230001
电话：+86(0551)65177518 ext:
传真：+86(0551)6260 7155
邮箱：hfsimple@mail.hf.ah.cn
• 品展国际贸易(上海)有限公司（上海）
上海外高桥保税区泰谷路18号1号楼1105A室
邮编：200003
电话：+86(0512) 6808 6023
传真：+86(0512) 6808 6025
邮箱：melody@chtek.com.tw
官网：chtek.com.tw
• 广州康祺科技发展有限公司（广州）
广州市天河区华强路1号珠控国际中心8层06单元
邮编：510623
电话：020-38295200
传真：020-38295122
邮箱：baobao@kontchi.com
• 广州科欣仪器有限公司（广州）
广州市黄埔区黄埔大道933号209室
邮编：510700
电话：86-20-38699788
传真：86-20-34395932
邮箱：cs@gzkexin.com.cn
• 成都安诚迅飞电子科技有限公司（成都）
成都市武侯区人民南路四段27号1栋1单元 24层3号
邮编：610041
电话：028-86027579
邮箱：jincai.he@ancentest.com
• 新亚制程（浙江）股份有限公司（深圳）
深圳市福田区中康路卓越城梅林中心广场（北区）一期1栋3楼
邮编：518035
电话：0755-23818536
传真：0755-23818625
邮箱：wangrongbin@sunyes.cn
• 无锡市邦达测量科技有限公司（无锡）
江苏省无锡市新区长江北路112号
邮编：214028
电话：0510-85258521 ext:
邮箱：bdyiqi@bdyiqi.com
• 武汉力德仪测科技有限公司（武汉）
武汉市光谷大道54号国际企业中心四期A座501室
邮编：430074
电话：027-85481090 ext:
邮箱：liuyang@leader-e.com
• 苏州工业园区贝奇仪器有限公司（苏州）
苏州工业园区通园路398号海逸大厦A402室
邮编：215006
电话：0512-62883832
邮箱：szbeiqi@szbeiqi.net
• 青岛鲁芯仪器有限公司（青岛）
青岛市福州北路135号鼎都1号写字楼328室
邮编：266007
电话：15953279543
传真：0532-80669058-830
邮箱：gaochangyuan@qdluxin.com
• Avnet Electronics Marketing（Phoenix）
2211 South 47th Street
邮编：85034
电话：+65 6289 9164
邮箱：Josephine.Cheong@avnet.com
官网：OnlineSupportAsia@Avnet.com
• RFMW, Ltd.（San Jose）
188 Martinvale Lane
邮编：95119
电话：#09-129
邮箱：sales@rfmw.asia
官网：www.rfmw.com
• 沈阳实拓科技有限公司（沈阳）
沈阳市和平区三好街35号8层
邮编：110004
电话：024-23843636
传真：024-23905232
邮箱：lf@shituokeji.cn
• 領先科儀有限公司（香港）
新界荃灣海盛路3號TML廣場21樓B5室
邮编：.
电话：852-31523600
传真：852-31523608
邮箱：allenma@advanceinst.com
租赁合作伙伴
• 深圳君鉴科技股份有限公司（深圳市）
光明街道观光路华强创意产业园3栋B座12楼光明新区
邮编：518107
电话：400-860-3035
邮箱：shichang@chrent.com
• 益莱储（北京）检测设备租赁有限公司（北京市）
来广营高科技产业园区4号楼3层301朝阳区
邮编：100102
电话：400-819-2800
邮箱：jim.chen@electrorent.com
• 北京东方中科集成科技股份有限公司科技租赁事业部（北京市）
北京市海淀区阜成路67号银都大厦12层
邮编：100142
电话：400-650-5566
传真：010-68728001
邮箱：wangml@oimec.com.cn
• 客而禧设备租赁（上海）有限公司（Shanghai）
徐汇区古美路1515号19号楼903室
邮编：201102
电话：021-54453166
邮箱：krc@krcchina.com
• 深圳市瑞普高电子有限公司（深圳市）
天安云谷产业园一期3栋D座1505-1506龙岗区
邮编：518129
电话：0755-29050100
邮箱：rickluo@ruipugao.com
• 苏州锦凡精密仪器科技有限公司（苏州）
苏州市高新区滨河路625号创业大厦5幢505
邮编：215011
电话：18914031336
邮箱：18914031336@jfsz.net
解决方案合作伙伴
• Tokyo Weld Co., Ltd.（Ota-ku）
2-28-1 Kitamagome
邮编：143-0021
电话：81-3-3775-4331
传真：81-3-3775-4359
邮箱：d-imai@tokyoweld.com
• 上海恒榉电子科技有限公司（Shanghai）
上海市奉贤区南桥镇西闸公路1036号3栋2层
邮编：201401
电话：18112779808
邮箱：salesvalue@everise-hj.com
• 佳燁科技股份有限公司(Ghiatek)（桃園市龜山區）
光明街243巷2號
邮编：33372
电话：+886-3-350-9960
传真：+886-3-320-3475
邮箱：support@ghiatek.com
• 华美博科技（北京）有限公司（北京市）
蓝靛厂东路2号金源时代商务中心C座9A2海淀区
邮编：100097
电话：010-88598732
邮箱：sino@sino-microtech.com
• 和创联合科技（北京）有限公司（北京市）
中关村东路18号财智国际大厦A座1612海淀区
邮编：100083
电话：400 650 7802
邮箱：info@hisuntest.com
• 昆山捷得立电子有限公司（昆山市）
登云路288号海创大厦C座25楼
邮编：215316
电话：0512-36831748
邮箱：sales@jiedeli-china.com
• 深圳市捷泰普科技有限公司（深圳市）
宝安区西乡街道前进二路桃源居南面深圳市智汇创新中心A座216室
邮编：518126
电话：0755-83908488
邮箱：sales@jtptech.cn
• 深圳市易捷测试技术有限公司（深圳市）
福虹路9号世贸广场C座1203室福田区
邮编：518033
电话：0755-83698930
邮箱：dongni.zhang@gbit.net.cn
官网：gbit.net.cn
• 深圳市泰仕捷科技有限公司（深圳市）
松岗大道7号汉海达大厦616室宝安区
邮编：518105
电话：0755-27128586
邮箱：riky.gua@tesijet.com
• 深圳市蓉声科技有限公司（深圳市）
福中路海连大厦连天阁 1103 室福田区
邮编：518033
电话：13828880571
邮箱：jiang.qian@radiation-test.com
• 苏州伊欧陆系统集成有限公司（苏州）
星湖街218号生物纳米园A7楼305室苏州工业园区
邮编：215000
电话：4008808776
邮箱：info@eoulu.com
• EM Labs Inc.（Kobe）
1-4-13 Mizukasadori, Nagata
邮编：653-0842
电话：+81-50-5370-0262
邮箱：info@emlabs.jp
• MPI Corporation（Chupei）
No. 155 Chungho Street
邮编：302
电话：+886-3-555-1771
传真：+886-3-551-8381
邮箱：info@mpi-corporation.com
官网：www.mpi-corporation.com/ast
• NOFFZ（Tönisvorst）
Vorster Strasse 238
邮编：47918
电话：+49 2151-99878-0
邮箱：info@noffz.com
• Power Technology Solutions（Santa Clara）
3048 Scott Blvd
邮编：95054
电话：650-308-8091 ext:
传真：408-727-0827
邮箱：inquiries@pwrts.com
• Resillion（Hasselt）
Kempische Steenweg 303
邮编：3500
电话：+32 498 92 01 71
邮箱：global-ci-sales@resillion.com
• Suzhou Link Ways Tech Co., Ltd.（Suzhou）
16F, Block B, Jin Shi Wang Hu Building, No. 18, Jia Rui alley, SIP
邮编：215021
电话：+86 512 6602 8998
• 上海凌测电子科技有限公司（上海）
峨山路91弄120号陆家嘴软件园8号楼401A室浦东新区
邮编：200127
电话：021-61090608
邮箱：yue.lin@merlintest.com.cn
• 上海北汇信息科技有限公司（上海市）
秀路100号虹桥总部1号4号楼3C闵行区紫
邮编：201103
电话：021-34716271
邮箱：info@polelink.com
官网：polelink.com
• 上海怿星电子科技有限公司（上海市）
钦州北路1199号智汇园87号楼5F室徐汇区
邮编：200233
电话：021-64955659
邮箱：biz@e-planet.cn
• 东昇电磁兼容技术(深圳)有限公司（深圳市）
福田中心区26-3路中国凤凰大厦2栋25G
邮编：518026
电话：0755-82792411
邮箱：sales@jstoyo.cn
• 南京派格测控科技有限公司（南京市）
建邺区建邺人才服务大厦16楼
邮编：210019
电话：4008920858
邮箱：sales@pgtec.cn
官网：pgtec.cn
• 南京纳特通信电子有限公司（南京市）
江宁开发区临淮街20号
邮编：210012
电话：025-84471796
邮箱：sales@rflight.cn
• 深圳市研辰科技有限公司（深圳市）
益田路3008号皇都广场C座2815室福田区
邮编：518048
电话：0755-82828703
邮箱：roger_huang@ascentest.com
原厂翻新与二手仪器
• 是德科技原厂二手仪器商城（Keysight Certified Pre-Owned）：www.keysight.com/used/cn/zh/
• 原厂翻新仪器经与新品相同的最终测试与校准，原厂保修最长 5 年；享 40%–90% 折扣，另有线上 5% / 教育 15% 优惠
0条提问
X
提问
X
回答
暂无视频
0条口碑
X
发表口碑
粤公网安备44030902003758